FCC Peripheral Configuration

Select the input pin number.

Select this option to enable connection to the digital port to output the status of the boundary flag.

Select pin number for the digital port that outputs the boundary flag status.

Dependencies

To enable this parameter, select the Enable boundary flag output port parameter.

Select the input mode for the FCC pin.

Select the strength of output pins.

Dependencies

To enable this parameter, select the Enable boundary flag output port parameter.

Select the speed of FCC pin.

Select the voltage level of the FCC pin.

Specify the initial value for the threshold update.

Dependencies

To enable this parameter, set the Mode parameter to Normal or Hysteresis in the FCC block in the Simulink^® model.

Set the type of trigger to Software trigger - Sample Time or Hardware trigger to update the threshold value during run time.

Dependencies

To enable this parameter, set the Mode parameter to Normal or Hysteresis in the FCC block in the Simulink model.

Select the source of the hardware trigger to update the threshold value during run time.

Dependencies

To enable this parameter, set the Threshold update on parameter to Hardware trigger.

Select hardware trigger to update the threshold value during run time.

Dependencies

This parameter appears only if you select the Threshold update on parameter as Hardware trigger.

Select the type of hardware trigger edge to update the threshold value during run time.

Dependencies

To enable this parameter, set the Threshold update on parameter to Hardware trigger.

Specify the trigger delay to update the threshold value during run time.

Dependencies

To enable this parameter, set the Threshold update on parameter to Hardware trigger.

Specify the upper delta limit for the threshold value in the hysteresis mode of operation.

Dependencies

To enable this parameter, set the Mode parameter to Hysteresis in the FCC block in the Simulink model.

Specify the lower delta limit for the threshold value in the hysteresis mode of operation.

Dependencies

To enable this parameter, set the Mode parameter to Hysteresis in the FCC block in the Simulink model.

Specify the initial threshold value at the start of the ramp mode of operation.

Dependencies

To enable this parameter, set the Mode parameter to Ramp in the FCC block in the Simulink model.

Specify the initial threshold value at the end of the ramp mode of operation.

Dependencies

To enable this parameter, set the Mode parameter to Ramp in the FCC block in the Simulink model.

Specify the initial step width of the ramp.

Dependencies

To enable this parameter, set the Mode parameter to Ramp in the FCC block in the Simulink model.

Specify the initial step size of the ramp.

Dependencies

To enable this parameter, set the Mode parameter to Ramp in the FCC block in the Simulink model.

Select the trigger source to start the ramp.

Dependencies

To enable this parameter, set the Mode parameter to Ramp in the FCC block in the Simulink model.

Specify the trigger or source to end of the ramp. You can select the Boundary flag transition or End of threshold value option if you set the Ramp start on parameter to Software trigger - Sample time.

Dependencies

To enable this parameter, set the Mode parameter to Ramp in the FCC block in the Simulink model.

Select the source of the hardware trigger.

Dependencies

To enable this parameter, set the Ramp start on parameter to Hardware trigger.

Select the hardware trigger for the threshold update in the ramp mode.

Dependencies

To enable this parameter, set the Ramp start on parameter to Hardware trigger or Ramp end on parameter as Hardware trigger or End of threshold value.

Select the type of the hardware trigger edge for the threshold update in the ramp mode.

Dependencies

To enable this parameter, set the Ramp start on parameter to Hardware trigger or the Ramp end on parameter to Hardware trigger or End of threshold value.

Specify the trigger delay for threshold update in ramp mode.

Dependencies

To enable this parameter, set the Ramp start on parameter to Hardware trigger or the Ramp end on parameter to Hardware trigger or End of threshold value.

Specify the number of glitches to filter out in the input signal.

Activate boundary flag based on threshold value.

Specify when to enable the boundary flag.

Specify the source of gate signal to enable the boundary flag.

Dependencies

To enable this parameter, set the Flag enable on parameter to Gate High or Gate Low.

Select hardware trigger to enable the boundary flag.

Dependencies

To enable this parameter, set the Flag enable on parameter to Gate High or Gate Low.

Select the type of hardware trigger edge to enable the boundary flag

Dependencies

To enable this parameter, set the Flag enable on parameter to Gate High or Gate Low.

Specify the gate trigger delay to enable the boundary flag.

Dependencies

To enable this parameter, set the Flag enable on parameter to Gate High or Gate Low.

Specify the number of boundary flag connections.

Specify the module for boundary flag connections.

Dependencies

To enable this parameter, set the Number of connections parameter to a value greater than 0.

Specify the channels for the PWM module selected.

Dependencies

To enable this parameter, set the Number of connections parameter to a value greater than 0.

Service request based on boundary flag edges.

Service request based on the mode of the threshold update. You can select the option End of ramp in Ramp mode and New threshold update in Normalor Hysteresis mode of operation.