Main Content

Unipolar Stepper Motor Driver

Driver for unipolar stepper motor

  • Unipolar Stepper Motor Driver block

Libraries:
Simscape / Electrical / Electromechanical / Reluctance & Stepper

Description

The Unipolar Stepper Motor Driver block represents a driver specifically configured for use with the Unipolar Stepper Motor block. It connects the two winding center-tap connections A0 and B0 to the positive supply with a voltage equal to the value you provide for the Output voltage amplitude parameter. The A+, A-, B+, and B- ports are grounded in the appropriate sequence to create the stepping motion. The block initiates a step each time the voltage at the ENA port rises above the Enable threshold voltage parameter value.

If the voltage at the REV port is less than or equal to the Reverse threshold voltage parameter value, pulse A leads pulse B by 90 degrees. If the voltage at the REV port is greater than the Reverse threshold voltage value, pulse B leads pulse A by 90 degrees and the motor direction is reversed.

At time zero, A- and B+ are grounded.

If you set the Stepping mode parameter to Half stepping, the Unipolar Stepper Motor Driver block can produce the output waveforms required for half stepping. In this mode, there is an intermediate state between the full steps, in which just one of the A or the B half-windings is powered. As a result, the step size is half of the stepper motor’s full step size. At half steps, windings that are not powered are short-circuited. This approximates the effect of a freewheeling diode connected across the windings.

Averaged Mode

If you set the Simulation mode parameter to Averaged, both for a Unipolar Stepper Motor Driver block and for the Unipolar Stepper Motor block connected to it, then the individual steps are not simulated. This can be a good way to speed up simulation. The Averaged mode assumes that the external controller provides a step rate demand. This step rate demand is determined from the voltage applied between the ENA and REF ports on the Unipolar Stepper Motor Driver block, by multiplying this voltage by the value of the Step rate sensitivity parameter. The rotation direction is set by the REF port in the same way as for the Stepping mode.

Averaged mode needs to communicate the step rate demand and also output voltage amplitude information to the Unipolar Stepper Motor block. To do this, the step rate demand is applied as an equivalent voltage across the A+ and A- ports. Similarly the output voltage amplitude information is conveyed by applying a steady-state voltage across the B+ and B- ports with value equal to the Output voltage amplitude parameter.

Examples

Assumptions and Limitations

  • To use Averaged mode, the Unipolar Stepper Motor Driver block must be directly connected to a Unipolar Stepper Motor block also running in Averaged mode.

  • When changing from Stepping to Averaged mode and back, you will need to modify your upstream blocks that provide the input voltages to the Unipolar Stepper Motor Driver. One way to achieve this easily is to use Simulink® variant subsystems.

Ports

Conserving

expand all

Electrical conserving port associated with the top A-phase electrical connection.

Electrical conserving port associated with the A-phase center tap connection.

Electrical conserving port associated with the lower A-phase electrical connection.

Electrical conserving port associated with the top B-phase electrical connection.

Electrical conserving port associated with the B-phase center tap connection.

Electrical conserving port associated with the lower B-phase electrical connection.

Electrical conserving port associated with the triggering input step voltage.

Electrical conserving port associated with the input floating reference voltage.

Electrical conserving port associated with the voltage that controls motor direction.

Parameters

expand all

Select Stepping or Averaged. Use Averaged only if the block is connected directly to a Unipolar Stepper Motor block also running in Averaged mode.

This parameter converts the voltage presented across the ENA and REF ports into a step rate demand.

Dependencies

This parameter is visible only when you set the Simulation mode parameter to Averaged.

When the voltage at the ENA port rises above this threshold, the Unipolar Stepper Motor Driver block initiates a step.

Dependencies

This parameter is visible only when you set the Simulation mode parameter to Stepping.

When the voltage at the REV port rises above this threshold, pulse B leads pulse A by 90 degrees, and the motor direction is reversed.

Amplitude of the output pulse trains.

Select Full stepping or Half stepping.

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.

Version History

Introduced in R2014a