How to customize a Built-in PID Block?

6 次查看（过去 30 天）
Mike
Mike 2012-10-3
I am using a PID controller in a feedback system. I need to change the gain's multiplication type from element-wise to the matrix. I right clicked on the PID block then from link options, I disabled the link. Now after I looked under the mask, I could change the Gain's multiplication type. but after I save the model and run the simulation again everything goes back to its initial settings like I never applied any change! So my question is How can I customize the PID block in SIMULINK?
  2 个评论
Ryan G
Ryan G 2012-10-8
Since you are doing matrix multiplication are you implying that this will have more than 1 input to the PID?
Mike
Mike 2012-10-8
Yes, i have 6 inputs. 3 of them are positions and others are velocities.
i uploaded my model so you can take a look inside it easier. http://fs1.filegir.com/pamadour/model.zip run Main.m it will execute the model automatically. first the model should run without any errors because i am using my own PID block (blue block). then you can substitute this with the MATLAB's built-in block (it exists unattached above the model), although i have set all initial fcn's but still it doesn't work. please note that the PID gains are P, I and D which come from the workspace.

请先登录，再进行评论。

请先登录，再回答此问题。

采纳的回答

Arkadiy Turevskiy
Arkadiy Turevskiy 2012-10-8
编辑：Arkadiy Turevskiy 2012-10-8
Hello Mike,
At the moment, you won't be able to customize the standard PID block and still retain the automatic tuning functionality. The best workaround I can suggest is creating your own block for implementation, and using the standard block for tuning. Once the gain are tuned using the standard block, you can use them in your customized block. You could probably somewhat automate the process by using block callbacks and variants.
Arkadiy
  2 个评论
Mike
Mike 2012-10-8
Dear Arkadiy
Thanks for your answer but how can i use Standard block for tuning while using it causes errors in my system?
Standard blocks use element-wise multiplication which cause to dimension error. if the multiplication type is matrix no error will occur. you can look at my system here: http://fs1.filegir.com/pamadour/model.zip
Arkadiy Turevskiy
Arkadiy Turevskiy 2012-10-19
Hello Mike, PID Controller block in Simulink, as well as the PID Tuner, only work on SISO systems. For a MIMO system, you need to specify your controller as a set of SISO PID loops. PID Tuner would not be able to tune a multi-loop design, you will need to use tools from Robust Control Toolbox, like shown in this example.
Arkadiy

请先登录，再进行评论。

更多回答（2 个）

Azzi Abdelmalek
Azzi Abdelmalek 2012-10-4
编辑：Azzi Abdelmalek 2012-10-4
I see your problem, but you can change these setting by code, just after loading your model named 'model.mdl'
set_param('model/PID Controller/Proportional Gain','Multiplication','Matrix(K*u)')
or you can associate this code with your model:
right click on your model- properties-callbacks-init Fcn (copy and paste the code)
  10 个评论
显示 8更早的评论
Azzi Abdelmalek
Azzi Abdelmalek 2012-10-6
编辑：Azzi Abdelmalek 2012-10-6
I think the setting vanishes just when the simultion start, not after like I said. I suggest to Edit mask of your PID block then unmask it. when you start simulations other errors will occur, asking about:
  • output/param (min/max). set them to []
  • datatype(etc...) set them to double
save the target of this link
http://azzimalikcom.ipage.com/model_main2.mdl
Mike
Mike 2012-10-7
Thanks, but it is like the controller which I made by my own. I can't use PID Tuner in this case.

请先登录，再进行评论。

Babak
Babak 2012-10-3
You don't want to edit Simulink's Built in blocks.
Instead you want to create your own custom blocks. You could do it with creating an S-function block and creating a mask for it or making a MATLAB based block which runs an m-file.
  1 个评论
Mike
Mike 2012-10-3
Dear Babak
I can create a simple PID controller in Simulink. but the Matlab's built-in PID block has advanced features Like "Tune" which helps me to select the proper Gain coefficients by visualizing the overshoot, settling time.. etc.
that's why i need to find a way to customize the Simulink's built-in PID block.

请先登录，再进行评论。

类别

在 Help Center 和 File Exchange 中查找有关 Classical Control Design 的更多信息

标签

产品

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by