Martin

Last seen: 19 days 前 | 自 2011 起处于活动状态

Followers: 0 Following: 0

联系

统计数据

All

Feeds

已回答
Simscape Tank (G-TL) Elevation from a reference
The best way may be to use the Pipe (TL) block in Simscape Fluids. Closed conduit that transports fluid between thermal liquid ...

7 months 前 | 0

已回答
Why are my simulink initial conditions sometimes not met, despite high priority?
When selecting Start simulation from steady state, the solver tries to find what the model would go to after a very long simulat...

7 months 前 | 0

已回答
How can I model an Elbow in Simspace while using the TL library?
Elbows are available in the Thermal Liquid library in Simscape Fluids as of R2022a. Pipe turn in a thermal liquid network - MAT...

7 months 前 | 0

已回答
Interface (TL-IL) variable temperature
Thermal liquid elbows have been added as of R2022a. Pipe turn in a thermal liquid network - MATLAB (mathworks.com)

7 months 前 | 0

已回答
Simulate interface between a Thermal Liquid and Two-Phase Fluid
Models heat exchange between a thermal liquid network and a network that can undergo phase change - MATLAB (mathworks.com) A mo...

7 months 前 | 0

已回答
how do I use run-time parameter with simscape gas-charged accumulator
I know that this is an older question. As of a few years ago, all parameters in the Gas-charged Accumulator are run-time capable...

7 months 前 | 0

已回答
How to access to two-phase fluid properties during run
This might be the block that you need: Measure temperature, density, specific enthalpy, specific entropy, and specific volume in...

7 months 前 | 0

已回答
How can I simulate jamming fault at a certain time?
One possibility would be to use the Rotational Damper in Simscape Driveline: Linear rotational damper - MATLAB (mathworks.com) ...

7 months 前 | 0

已回答
Simulink Model DC Motor with Transmission Gear
Please see Vehicle in Simscape Driveline and Simulink - MATLAB & Simulink (mathworks.com). It shows both Simulink and Simscape D...

7 months 前 | 0

已回答
Problems with moving Simscape from 2014b to 2015b
MathWorks does not guarantee behavior when files are saved in a newer release and then opened on an older release. In this case,...

7 months 前 | 0

已回答
Add Reset Function to Simscape Integrator Block
The PS Integrator was updated in R2021a to provide this functionality. The source code is available for that block as well. PS ...

1 year 前 | 0

已回答
i want to learn about the oxygen concentrator example in simscape matlab ?
Hello Hassan, You can find information about it here: Oxygen Concentrator - MATLAB & Simulink (mathworks.com)

3 years 前 | 0

已回答
Negative velocity curve from vehicle body block
Hi Vinay, It is difficult to say what happened, but it looks like recreating the subsystem worked. It may be possible that some...

3 years 前 | 0

已回答
Source Code Condenser Code
Hi Rainer, A Condenser/Evaporator with two-phase fluid on one side and moist air on the other was introduced in R2019a. A Cond...

3 years 前 | 0

已回答
Unexpected dog clutch disengagement behavior
Hello Frank, Thank you for including the example model to demonstrate the issue. The translational behavior of the shift link...

3 years 前 | 1

已回答
Unable to open the following model in R2019a trial version.
Hi Sadeer, It looks like the installation is not complete, or the path is incorrect. Definitely contact technical support for...

3 years 前 | 0

已回答
Simple gear model with load dependent efficiency
Hi Mahesh, The load-dependent efficiency model assumes that torque loss is equal to a constant value plus an additional loss ...

3 years 前 | 0

已回答
How is inertia in planetary gear block calculated?
Hello David, Yes, connecting the carrier port would be the carrier inertia. The planet inertia is the sum of all the planet g...

4 years 前 | 0

已回答
I am getting the following error in simscape driveline please help
Hello Mastrieo, This could be due to an overconstrained model. Check to see if you have conflicting parts of the model, for e...

4 years 前 | 0

已回答
Thermal behaviour of Harmonic Drive Simulink
Hello Kotryna, Some of this may have been addressed in your other questions. I would also check the Solver Configuration bloc...

4 years 前 | 0

已回答
Can't find 'Drive Cycle Source' blockset in Simcsape/Simulink.
Hello Rohan, The Drive Cycle Source is part of the Powertrain Blockset. Check to see if you have that product installed. M...

4 years 前 | 0

| 已接受

已回答
"First solve for initial conditions failed to converge." Thermal model
Hello Kotryna, The temperature on those blocks is a difference, not absolute. Also focus on specifying the differential varia...

4 years 前 | 0

已回答
Initial temperature harmonic drive gear
Hi Kotryana, As a first step, I would look at the Variable Viewer to see what is met and what is not. In the toolstrip, selec...

4 years 前 | 0

已回答
Generic engine oscillating output
Hi Stephen, This looks like the oscillation is due to the interactions between the slipping pullies in the two belt drives. I...

4 years 前 | 0

已回答
Quarter model with tire (Magic Formula) SimScape Driveline
Hello Marcin, The H port is a translational conserving port associated with the hub of the tire. It should be associated with...

4 years 前 | 0

| 已接受

已回答
Is it usually used Simscape Driveline for designing the powertrain of a diesel-electric locomotive? Are there any examples about trains?
Hello Stefania, While we do not have any shipping examples regarding trains, users have successfully used Simscape Driveline ...

4 years 前 | 0

已回答
How can i see the output torque of a gearbox
Hello Sree, If you need the value during simulation, you could add a Torque Sensor from the Simscape Foundation Library in se...

4 years 前 | 0

已回答
Looking for Leadscrew model in library and not found.
Hello Orlando, Do you have Simscape Driveline installed? This block is in the Simscape Driveline library under Gears and Rota...

4 years 前 | 0

| 已接受

已回答
Torque vector must be arranged in strictly ascending order.
The block is not erroring because of the torque vector given on the Engine Torque tab. Speed is the independent vector that must...

4 years 前 | 0

已回答
Disk Friction Clutch - OPEN clutch
Hello Berkan, There are two types of kinetic friction in the model. The kinetic friction of the clutch plates pushing against...

4 years 前 | 0

加载更多