已回答
Is it possible to use two or more GPUs with the UAV Toolbox simultaneously?
Hi @Jones, Thanks for your update. Noted that you're using UAV Toolbox for UAV simulation with HIL and integrating aerodyn...

12 days 前 | 0

已回答
MATLAB won't invert a function in the Laplace domain...
Hi @John, I took a look at your gamma distribution Laplace inversion problem, and you've hit a classic limitation of MATLAB's...

14 days 前 | 0

已回答
C2000 CMPSS to ePWM Trip Zone / Digital Compare connection
Hi @Valeriy, Thank you for your detailed question regarding overcurrent protection on the Delfino F28377S MCU using CMPSS and...

15 days 前 | 0

已回答
blfread with CAN-frame and J1939-frame
Hi @Florian, Thanks for your question regarding reading J1939 frames using `blfread('myBLF.blf')`. I understand you're seeing...

15 days 前 | 0

已回答
C Caller error when passing 2D array inside struct via Simulink bus
Hi @ 주형, I understand the compilation error you're encountering with the C Caller block when passing 2D arrays within structs...

15 days 前 | 0

| 已接受

已回答
create array and plot the function
Dear @SP, I'm writing to follow up on your MATLAB implementation from October 29, 2018, and to address the recent technic...

15 days 前 | 0

已回答
How to correctly implement a pid control and fuzzy logic control on synchronous generator tied to ieee bus system?
Hi @Frans, I've conducted a thorough analysis of the latest MathWorks documentation and your Simulink model for implement...

17 days 前 | 0

| 已接受

已回答
Incorrect calculation between CRS coordinate transformation
Hi @Cristobal, I reviewed the workflow for converting coordinates from *EPSG:2084 (Hito XVIII 1963 / UTM 19S)* to *EPSG:32719...

19 days 前 | 0

| 已接受

已回答
Neumann boundary condition in a diagonal matrix
Hi @Hugo, Thanks for sharing your code and the detailed explanation of your approach. I see you're trying to increase the a...

19 days 前 | 0

已回答
HYBRID ENERGY STORAGE SYSTEM SUPERCAPACITOR BATTERY OFF-GRID SOLAR POWER SYSTEM
Hi @Muhammad, Thank you for sharing your simulation files and the detailed discussion thread. I've carefully reviewed all you...

20 days 前 | 0

已回答
Coriolis Matrix of a 14 DOF bipedal robot won't compile its matlab function
Hi @Giovanni Maria, After spending several hours researching MATLAB documentation and robotics literature online, I believe I...

20 days 前 | 0

| 已接受

已回答
Please provide me the matlab code for 8-bit integer arithmetic coding and decoding.
Hi @Harpreet, I understand you're encountering issues with reconstructing a binary vector after arithmetic encoding and decod...

21 days 前 | 0

已回答
how to find similiarity of peak/pattern time series?
Hi @Nirwana, Thank you for sharing your code and detailing your analysis objectives. I understand that your primary goal is t...

21 days 前 | 0

已回答
Error in building simulink code for PX4-V6x
Hi @Thai Hoa, Thank you for sharing your challenge regarding compilation of Simulink-generated code for the PX4 FMU V6X. Alth...

22 days 前 | 0

| 已接受

已回答
Building and Embedding a Reduced Order Model in National Instruments Hardware (cRIO)
Hi @Patrick, *Original Request*: " _I could do with some guidance on a task required on a National Instruments (NI) LEM contr...

23 days 前 | 0

已回答
Scatter point plot into plot3d or any surface
Hi @Hugo David, I saw your question about creating a surface from your scattered x,y,z data points. Yes, you can definitely m...

25 days 前 | 1

已解决

Basic Mathematics 2
If a 4’ x 8’ sheet of ½” plywood weighs W lbs and you cut an L” x L” robot base from this material, approximately how much weigh...

25 days 前

已解决

Calculate load on arm 1
A robot is designed with a motor directly attached at the pivot point of the lifting arm. The L inch arm has a weight of W1 lbs...

25 days 前

已解决

Mechanical Advantage of a Gear Train
Calculate the mechanical advantage of a gear train. The mechanical advantage of a gear couple is given by MA = T_o/T_i where ...

25 days 前

已解决

Calculate the acceleration of a crate
What is the acceleration of a crate if two robots apply F1 N and F2 N of force respectively and a frictional force of FR N acts ...

25 days 前

已解决

Coefficient of Kinetic friction
A robot exerts a F1 lb. force horizontally on a W lb. crate across a concrete floor at a constant speed. What is the coefficien...

25 days 前

已解决

Current through resistor
Three resistors (R2, R3, R4) are connected in parallel as shown in the figure. If this combination is connected in series with ...

25 days 前

已回答
Export an Image as a Geotiff that is not aligned with Lat/Long Grid
Hi @Richard, Thank you for your detailed question. Based on your description, here’s how you can handle your rotated image an...

26 days 前 | 0

| 已接受

已回答
BILSTM input data length
Hi @Walid, Yes, you can input short feature vectors to BiLSTM networks, though this requires proper data formatting. BiLSTM l...

27 days 前 | 1

已回答
Unable to fit HDL coder design into FPGA
Hi @John, I don’t currently have access to Simulink or MATLAB toolboxes to replicate your setup directly, but I reviewed Math...

28 days 前 | 0

| 已接受

已回答
Why my PLUTO cant capture the signals
Hi @Mert, Based on the RX code you shared and your comment about not receiving signals on a different PC with a different ADA...

29 days 前 | 0

已回答
function argument pow error
Hi @Cesar, Let me address your comment:” _not sure why I'm getting this error, any help will be appreciated. thanks_" The ...

30 days 前 | 1

| 已接受

已回答
Generation of proto and thunk files for distribution
Hi @Eric, To automate proto and thunk file generation in a CI/CD process, a headless MATLAB environment (or MATLAB Docker image...

1 month 前 | 0

已回答
Issues with nlinfit - not fitting second parameter? Fitting a Blackbody curve
Hi @Caelan, Thank you for sharing your code and detailed description of the issues. I have reviewed your approach and specifi...

1 month 前 | 0

| 已接受

已回答
Issue using combined slip wheel 2Dof in high slip scenarios
Hi @Justin, Thank you for your detailed explanation of the problem. From your description, the instability during high-slip c...

1 month 前 | 0