已回答
Pass a plot handle into a function argument
figure(1) xx=linspace(-pi,pi,100); yy=sin(xx); plot(xx,yy,'r-','DisplayName','sinus'); legend; hold on; % then plot a se...

9 months 前 | 0

| 已接受

已回答
Breakpoint in Simulink MATLAB function block not working
Try sim("modelName","Debug","on")? https://www.mathworks.com/help/simulink/slref/sim.html

10 months 前 | 0

已回答
Sample Time from To Workspace not precise
If you use a ZOH block to measure the signal and specify the sample time of the ZOH block as Ts, then specify the sample time fo...

10 months 前 | 0

| 已接受

已回答
Cannot load a Mat file into Simulink
Most likely due to incorrect data format. Look at this page under "Load Array Data" section. https://www.mathworks.com/help/sim...

10 months 前 | 0

| 已接受

已回答
How can I find out the data type in the Simulink?
Click "Edit data" in the MATLAB Function block editor, you can set the data type of any data (input, output, data, etc.). Make s...

10 months 前 | 0

已回答
Extract variables saved to workspace from simulink
I would suggest you saving the data in time series format and use API to process it. https://www.mathworks.com/help/matlab/time...

10 months 前 | 0

| 已接受

已回答
Simulink Scope viewing problem
Is the data points limited? Check "View", "Configuration properties", "logging"

10 months 前 | 0

已回答
Delaying Signal Builder Start in Simulink
This can be done through an 1-D lookup table. The trick is the input. Use your Switch output to enable an Enabled SubSystem bl...

10 months 前 | 0

已回答
3-D Simulation Vehicle Ground Following
set_param('mcityMonoCamera/Simulation 3D Vehicle with Ground Following','LeftHeadlightOrientation','[15 0]')

10 months 前 | 0

已回答
Unable to extract time and data from simout MATLAB
As it indicates in the Simulink model, the data is saved in "out.simU". So, add "simX=out.simX;simU=out.simU;" in front of your ...

10 months 前 | 0

已回答
Delaying Signal Builder Start in Simulink
Try to put the Signal Builder block inside an Enabled Subsystem block.

10 months 前 | 0

已回答
How can I change the Debounce time in Stateflow?
Typically, the value "5" in the two "after(5,sec)" statements is the time that the switch state needs to stay (without bounce) b...

11 months 前 | 0

已回答
How I can fix this "resolve underspecified signal dimensions." error message ?
There is not enough info in the model to determine the size of "Xc". Double check your code, make sure "Xc" is initialized or as...

11 months 前 | 0

已回答
Vectorizing a Simulink Model
Simulink supports vector, so if designed carefully, a single Simulink subsystem could process N velocity and postion to generate...

11 months 前 | 0

已回答
Simulink - Saving Base Workspace Variables
There are at least two other ways. Once all the .m files are executed, you can use save() to save the base workspace to a .mat ...

11 months 前 | 1

| 已接受

已回答
Differences between the two Sample time settings in the MATLAB Function block in Simulink
This is a really good question. I've never noticed it before. I'll provide my take on it. You could contact the Mathworks' tech ...

11 months 前 | 0

| 已接受

已回答
the use of Integrator block in subsystem
When the sample time is set to be -1, it means the sample time is "inherited".

11 months 前 | 0

| 已接受

已回答
Is there any initialization block for parameters and constants in simulink model to be used throughout the model ?
Use a Simulink Data Dictionary (.sldd). Start from here https://www.mathworks.com/help/simulink/ug/migrate-models-to-use-dictio...

11 months 前 | 0

| 已接受

已回答
Simulink If block error "Port 1 must directly or indirectly connect to one If Action Subsystem"
Outport 1 of the If block is also connected to another destination but it was not shown in the snapshot. Dis-connect that branch...

11 months 前 | 0

已回答
Convert array of numbers to an array of padded strings
stanums = 7:12; s=sprintf('%02d\n',stanums(:))

11 months 前 | 0

已回答
Hello, can someone please help me understand this error?
If the pulse width is 87.85%, then the gap of the pulses will be 12.15%. Then you have to be able to distinguish at least 0.05% ...

11 months 前 | 0

| 已接受

已回答
How to do Simulink versioning
Mathworks has its own diff tool and it can be integrated with Git. Model Comparison

11 months 前 | 1

| 已接受

已回答
Creating new variable using different row and column chunks from a matrix
D=rand(29,46); Training1_T= [D(1:14,17:21);D(15:29,32:36)]

11 months 前 | 0

已回答
Hello, I need help to resolve this error, please.
Simulink now supports "string" data type. At your Simulink model, press Ctrl+H to bring up the Model Explorer. Navigate to the c...

11 months 前 | 0

已回答
Unable to convert the 2021 mdl to 2009b mdl
You can do this, but of course, if there are blocks that are available in R2021b but not in R2009b, then there could be issues. ...

11 months 前 | 0

已回答
extract a number N of equally spaced rows within a matrix
M=repmat((1:100)',1,2); N=7; d=M(round(linspace(1,height(M),N)),:)

11 months 前 | 0

| 已接受

已回答
Hello, could someone kindly assist me in resolving this error?
A Simulink model describes a "data flow". It is different than a "code flow", where "voltage_input" is just a variable stored in...

11 months 前 | 0

| 已接受

已回答
Algebraic loop error, how to solve?
There is no algebraic loop here. Giving what ever value to DELTA_U(k), "f" can be calculated without problem. If you feed the o...

11 months 前 | 0

| 已接受

已回答
Ramp rate %/min limiter in simulink
Feed constant value of 0.05 to "up" and -0.05 to "lo". If you want to prevent a value from increasing more than 5% per minute, t...

11 months 前 | 0

已回答
I want to access signal data in Subsystem from mask callback without using the base Workspace
Refer to this Q&A. https://www.mathworks.com/matlabcentral/answers/2003487-how-to-plot-simulation-results-in-a-gui-while-the-si...

11 months 前 | 0