已回答
position control of a bldc with gearbox
the same things i was implemented,if you need help contact me on electricmani@yahoo.co.in
position control of a bldc with gearbox
the same things i was implemented,if you need help contact me on electricmani@yahoo.co.in
8 years 前 | 0
已回答
controlling bldc via ESC+arduino and simulink
What you meant ESC, post clear functional block diagram
controlling bldc via ESC+arduino and simulink
What you meant ESC, post clear functional block diagram
8 years 前 | 0
已回答
How to limit the Pulse generator Pulses ?
It's required pulse decoder system as like QEP sensor. For more information on how to implement, contact me on electricmani@yaho...
How to limit the Pulse generator Pulses ?
It's required pulse decoder system as like QEP sensor. For more information on how to implement, contact me on electricmani@yaho...
8 years 前 | 0
已回答
suported hardware card to work with Simulink
There are lot of HW are avilable, http://in.mathworks.com/hardware-support/home.html. as per your requirement simple Arduino low...
suported hardware card to work with Simulink
There are lot of HW are avilable, http://in.mathworks.com/hardware-support/home.html. as per your requirement simple Arduino low...
8 years 前 | 0
已回答
How to interface dspace 1103 with non real simulation model of synchronous generator?
You can fully module your generator in mathematical equation and test with HIL.
How to interface dspace 1103 with non real simulation model of synchronous generator?
You can fully module your generator in mathematical equation and test with HIL.
8 years 前 | 0
已回答
Neural Network on dSpace
Try with buffer or change your input sample time greater then data samples. (Rate transition block may be helpful).
Neural Network on dSpace
Try with buffer or change your input sample time greater then data samples. (Rate transition block may be helpful).
8 years 前 | 0
提问
Difference between simulation of electric machines form mathematical modeling and model used from simpower system tools
Why the mathematical modeling and simulation of electrical machines results are not equal results with machine model used form s...
9 years 前 | 0 个回答 | 0
0
个回答已回答
how to develope the switching pulses for DTC of induction motor in dspace1104
You should use PWM output pulses instant of DAC, then seperate IGBT gate driver and opto isolator circuits should be connected. ...
how to develope the switching pulses for DTC of induction motor in dspace1104
You should use PWM output pulses instant of DAC, then seperate IGBT gate driver and opto isolator circuits should be connected. ...
10 years 前 | 0
已回答
how to run BLDC motor by means of Dspace hardware
Well mr.sebastian, why you use ADC for reading hall information instant of DIO, use DIO then you gat better faster performance t...
how to run BLDC motor by means of Dspace hardware
Well mr.sebastian, why you use ADC for reading hall information instant of DIO, use DIO then you gat better faster performance t...
10 years 前 | 0
已回答
Exporting data from dSPACE to matlab/Simulink
Refer the bellow links, this problem still not solved. http://www.mathworks.in/matlabcentral/answers/59293-how-to-run-simulin...
Exporting data from dSPACE to matlab/Simulink
Refer the bellow links, this problem still not solved. http://www.mathworks.in/matlabcentral/answers/59293-how-to-run-simulin...
10 years 前 | 0
提问
How to Measure Motor Speed?
Hi guys, I use DSP TMS320F2812 for control of BLDC drive. I used 3GPOI's are for detect rotor position from this correspond...
10 years 前 | 1 个回答 | 0
1
个回答已回答
May i know how to design the 3 phase converter for BLDC motor with Sinusoidal Commutation?
when you go sinusoidal pwm its known as pmsm or pmac. it should be operated in 180 degree conduction mode.
May i know how to design the 3 phase converter for BLDC motor with Sinusoidal Commutation?
when you go sinusoidal pwm its known as pmsm or pmac. it should be operated in 180 degree conduction mode.
10 years 前 | 0
已回答
RS232 MatLab Interface
i,m trying the same but i use simulink to show signal via scope, the output is not an exact data and it is not updating data reg...
RS232 MatLab Interface
i,m trying the same but i use simulink to show signal via scope, the output is not an exact data and it is not updating data reg...
10 years 前 | 0
已回答
How to interface DSP kit with MATLAB
you can use JTAG emulator to burn matlab code into DSP through CCS.
How to interface DSP kit with MATLAB
you can use JTAG emulator to burn matlab code into DSP through CCS.
11 years 前 | 0
已回答
XPC-target: Output data to Host pc
hi, try to save your data in to MS excel by using 'to file' tool.
XPC-target: Output data to Host pc
hi, try to save your data in to MS excel by using 'to file' tool.
11 years 前 | 0
提问
How to run simulink through dSPACE(DS1104) without control desk?
can any one help me how to run the simulink through dSPACE (DS1104) by changing external mode and to connect target link after b...
11 years 前 | 3 个回答 | 0
3
个回答提问
Initial position detection of sensor less BLDC motor drive
my research is sensor less speed control of BLDC motor drive, it's possible to detect ZCD of line voltage. but initial starting ...
11 years 前 | 1 个回答 | 0
1
个回答已提交
Sinusoidal Buck Boost AC Voltage Controller
Buck Boost AC Voltage Controller, Output Pure Sinusoidal
11 years 前 | 2 次下载 |
已回答
How to build BLDC motor in simulink?
convectional DC motor we cont change BLDC, instant you change Inverter fed Trapezoidal PMSM as BLDC motor.
How to build BLDC motor in simulink?
convectional DC motor we cont change BLDC, instant you change Inverter fed Trapezoidal PMSM as BLDC motor.
11 years 前 | 0
已回答
fuzzy logic controller
first you need to import and export the fis file, i know the fuzzy working but i need sensorless control of BLDC motor drive. if...
fuzzy logic controller
first you need to import and export the fis file, i know the fuzzy working but i need sensorless control of BLDC motor drive. if...
11 years 前 | 0
已回答
Electro Mechanical Actuator model using BLDC motor
if your input is mechanical mean select as TORQUE.
Electro Mechanical Actuator model using BLDC motor
if your input is mechanical mean select as TORQUE.
11 years 前 | 0
