已回答
Time dependent external heat flux in PDE Toolbox
Hi Pascal, You are on the right track, refer to the externalHeatFlux in the example: https://www.mathworks.com/help/pde/ug/h...

5 years 前 | 0

| 已接受

已回答
Unexpected Result for 3-D Thermal Transient Analysis of Heat sink using PDE Solver Toolbox
Here is the correct results using the new STL after fixing two more inconsitencies: Radiation problem should include temperatu...

5 years 前 | 1

| 已接受

已回答
Unexpected Result for 3-D Thermal Transient Analysis of Heat sink using PDE Solver Toolbox
Hello Jake, You seem to have unit mismatch in the MATLAB model. PDE Toolbox doesn't have any units. When you exported the geom...

5 years 前 | 1

已回答
Solving 2D Convection Diffusion Equation
You might be able to setup the 2-D version using PDE toolbox. Take look at the following code. Please verify I have accuratly ca...

5 years 前 | 0

| 已接受

已回答
Solving PDE for Hygromechanical Coupling with f coefficient as a function of previous PDE results
You should be all set if you replace the last two lines in your function with the following one line: fx = [gradx.'.*coefRGx;gr...

5 years 前 | 0

| 已接受

已回答
Error using deval in pde toolbox
Hi SS, The warning: Warning: Failure at t=1.307250e+00. Unable to meet integration tolerances without reducing the step size...

5 years 前 | 0

| 已接受

已回答
Temperature-dependent boundary conditions
Do you have PDE Toolbox in your installed products list? You can check this by executing 'ver' at the command prompt. If so, di...

5 years 前 | 0

| 已接受

已回答
Radiation in PDE thermal model
To activate both radiation and convection on the same boundary, combine them into one assignment as: thermalBC(thermalmodel,'Fa...

5 years 前 | 1

| 已接受

已回答
Temperature in a specific point with pde thermal
Yes! Check out the interpolateTemperature function.

5 years 前 | 0

已回答
How to specify initial conditions for two different subdomains in PDE solver?
I suggest you to look at the programmatic workflow, refer to the programmatic workflow overview doc page. In the programmatic ...

5 years 前 | 0

已回答
How to specify f coefficient function for arbitrarily located point sources within a domain.
If you want to use addtional arguments in computing f, then wrap the f coefficient function around the actual function that take...

5 years 前 | 0

已回答
Determine locations struct used in PDE solver
You can write that code that you indented to use to "create a matrix that is of length N by M where ..." in the function itself....

5 years 前 | 0

| 已接受

已回答
Time-dependent thermal conductivity
Function should return values of k at all points requested by the solver, points are in the first argument. Update your funciton...

5 years 前 | 0

| 已接受

已回答
Import of a 2D mesh created by Mesh2D or NodeLab into PDE Toolbox
You can import triangles in 2-D into PDE Toolbox using geometryFromMesh function. Although it creates geometry using the mesh da...

5 years 前 | 0

已回答
Usage of InternalHeatSource from PDE toolbox (Heat Transfer)
Value of internal hear source should be energy per unit volume. Are you sure your internalHeatSource command is getting executed...

5 years 前 | 0

已回答
Time-dependent internal heat source
You cannot add function handle as you have done, f+q in: specifyCoefficients(model,'m',0,'d',d,'c',c,'a',a,'f',f+q); I would r...

5 years 前 | 0

| 已接受

已回答
How I introduce a matrix form of c coefficient in PDE equation using solvepde matlab command
Output of c coefficient function should be a matrix or column vector of appropriate size, where the number of columns correspond...

5 years 前 | 0

已回答
Efficient sensor placement optimization
Not sure if I understand your question correctly. Are you referring to location mesh nodes when you say sensor? My guess is you...

5 years 前 | 0

已回答
Heat transfer question in pde toolbox
Yes, all the three properties can be defined as function of temperature. This will make the problem highly nonlinear, existance ...

5 years 前 | 0

已回答
How can I resolve the error "PDE coefficients cannot be function of solution or time." in a static solution of a PDE.
What are the output arguments in you function call InterpolateDisplacement? [UVdispB, UVdispT, UVdispL, UVdispR]=InterpolateDis...

5 years 前 | 0

已回答
How to create a copy of a pde model ?
Get hold of the handle that is provided as output, like: bc = applyBoundaryCondition(....) Now you can...

5 years 前 | 0

已回答
How to apply the boundary conditons to the mass and stiffness matrices?
Use the 'nullspace' as second argument, you will get matrices with BC imposed by eleminating dirichlet DoFs. Regards, Ravi

5 years 前 | 0

| 已接受

已回答
Cannot apply multiple, region-dependent thermal properties in PDE Toolbox
This is a bug where solver fails to distinguish the functions as seperate based on some queries. Workaround is to define variati...

5 years 前 | 1

已回答
How squareg works ?
Hi Pavel, I don't fully understand your question, but I can answer a portion on how to create square of different size. You can...

5 years 前 | 1

| 已接受

已回答
PDE tool box, internal heat generation and BC conditions
If the problem is axisymmetric, then you need follow the approach similar to this example: https://www.mathworks.com/help/pde/...

5 years 前 | 0

已回答
How can i define PDE coefficient which is scalar matrix inside the boundary
Hi Kim, Is your ffunc depends on solution, i.e., using state.u? Can you provide sample data, also xv and yv? Regards, Ravi ...

5 years 前 | 0

已回答
Boundary condition for multidomain geometry
Hi Urban, Would you be able to share your code and data? Geometric faces are identified by analyzing how drastic the normal ch...

5 years 前 | 0

已回答
Retrieving indices of times for a time-dependent system of PDEs within applyBoundaryCondition()
You need to create an interpolant object, see for example, griddedInterpolant. Construct interpolant (may be one for each N), an...

5 years 前 | 0

已回答
PDE Toolbox does not recognize subdomains in imported .stl geometry
STL with multiple bodies are imported as separate cells in PDE Toolbox. Essentially, the two cells are disconnected for analysis...

5 years 前 | 0

| 已接受

已回答
I find that the matlab official example "deflection-of-a-piezoelectric-actuator" cannot be correct
Hello Prof. Ciavarella, Can you provide a bit more details, reproduction code and expected results, of the modified setup to i...

5 years 前 | 0

| 已接受