Ethernet AXI Manager

Note

Ethernet AXI master has been renamed to Ethernet AXI manager and the UDP MATLAB^® as AXI Master IP has been renamed to the UDP AXI Manager IP. In the software and documentation, the terms "manager" and "subordinate" replace "master" and "slave," respectively.

Integrate and configure AXI manager over Ethernet using user datagram protocol (UDP). To use Ethernet AXI manager, you must first include these two intellectual property (IP) blocks in your project: Ethernet media access controller (MAC) Hub and UDP AXI Manager.

Ethernet MAC Hub IP

The Ethernet MAC Hub HDL IP supports the gigabit media independent interface (GMII). This Ethernet MAC Hub IP connects the Ethernet physical layer (PHY) to the UDP AXI Manager IP.

Interface of Ethernet MAC Hub IP

Interface of Ethernet MAC Hub IP

The interface of the Ethernet MAC Hub IP includes the ports in this table.

Port	Description
s_axis_0	AXI-stream subordinate interface. Connect this port to the m_axis port on the UDP AXI Manager IP.
m_axis_0	AXI-stream manager interface. Connect this port to the s_axis port on the UDP AXI Manager IP.

Ethernet MAC Hub IP Ports

Port	Direction	Description
ref_clk	Input	Reference clock signal that drives phy_gtxclk. The frequency of ref_clk must be the same as the phy_rxclk clock frequency.
ref_reset	Input	IP reset signal.
phy_rxclk	Input	Receive clock from PHY.
phy_rxd	Input	Receive data signal from PHY.
phy_rxdv	Input	Receive data valid control signal from PHY.
phy_rxer	Input	Receive error signal from PHY.
rxclk_en	Input	Receiver clock enable.
phy_gtxclk	Output	Clock to PHY.
phy_txd	Output	Transmit data signal to PHY.
phy_txen	Output	Transmit enable control signal to PHY.
phy_txer	Output	Transmit error signal to PHY.
txclk_en	Input	Transmitter clock enable.
phy_col	Input	Collision detect signal from PHY.
phy_crs	Input	Carrier sense detect signal from PHY.
axis_aclk	Input	Clock signal for AXI-stream interface.
axis_aresetn	Output	Active-low reset. Reset signal for AXI-stream interface. You can use this port to reset the downstream AXI peripherals.

Ethernet MAC Hub IP Parameters

After instantiating the Ethernet MAC Hub IP in your design, open the block parameters for configuration.

Ethernet MAC Hub IP parameters

Configure these parameters:

Number of AXI Stream Channels — This parameter decides the number of AXI-stream channels in the Ethernet MAC Hub IP. Select this value as an integer from 1 to 8. The default value is 1.
IP Address Byte1, IP Address Byte2, IP Address Byte3, IP Address Byte4 — These parameters set the four bytes in the range from 0 to 255 composing the UDP internet protocol (IP) address of the device. This address must match the DeviceAddress property value of the aximanager object.
UDP Port For Channel 1, UDP Port For Channel 2, UDP Port For Channel 3, UDP Port For Channel 4, UDP Port For Channel 5, UDP Port For Channel 6, UDP Port For Channel 7, UDP Port For Channel 8 — These parameters set the UDP port numbers. Specify each parameter value as an integer from 255 to 65,535. These port numbers must match the Port property value of the aximanager object.

UDP AXI Manager IP

The UDP AXI Manager HDL IP connects the Ethernet MAC Hub IP to your application IP. The UDP AXI Manager IP acts as a bridge that translates data between an AXI peripheral and MATLAB.

Interface of UDP AXI Manager IP

Interface of UDP AXI Manager IP

The interface of the UDP AXI Manager IP includes the ports in this table.

Port	Description
s_axis	AXI-stream subordinate interface.
m_axis	AXI-stream manager interface.
axi4_udp	AXI4-full manager interface.

UDP AXI Manager IP Ports

Port	Direction	Description
axis_aclk	Input	Clock signal for AXI-stream interface.
axis_aresetn	Input	Active-low reset signal for AXI-stream interface.
aclk	Input	Clock signal for AXI4-full interface.
aresetn	Input	Active-low reset. Reset signal for AXI4-full interface.

UDP AXI Manager IP Parameters

After instantiating the UDP AXI Manager IP in your design, open the block parameters for configuration.

UDP AXI Manager IP parameters

Configure these parameters:

ID Width — This parameter is the ID width in bits. Its value must match the ID width of the AXI4 subordinate.
AXI Data Width — This parameter is the data bus width in bits. The IP supports 32 bits or 64 bits.
AXI Address Width — This parameter is the address bus width in bits. The IP supports 32 bits or 64 bits.

When the program is running on your FPGA board, you can create an AXI manager object using the aximanager object. To access the subordinate memory locations on the board, use the readmemory and writememory object functions.

Related Examples

Access FPGA External Memory Using AXI Manager

More About

Set Up AXI Manager