Main Content

Encoder

Measure incremental position and direction of rotating motor

Since R2021a

expand all in page
  • Raspberry Pi Encoder block icon

Libraries:
Simulink Support Package for Raspberry Pi Hardware / Basic

Description

The Encoder block outputs the tick count from a quadrature encoder on a rotating motor connected to a Raspberry Pi® hardware board. Every increment in the tick count of the encoder indicates that the motor is rotating clockwise. Every decrement in the tick count of the encoder indicates that the motor is rotating counterclockwise. The total tick count represents the incremental position of the rotating motor.

You can reset the encoder readings from the block using the Reset mode parameter in the block parameters dialog box.

When simulating without hardware, this block outputs zeros. For more information, see Block Produces Zeros or Does Nothing in Simulation.

Ports

Input

expand all

Use this input port to reset the Encoder block tick counter.

When the value of the signal at the input port is 0, the block outputs the total tick count read from the encoder. In this case, the block output is the same as in the No reset mode. When the value of the signal at the input port is a nonzero value, the block outputs the number of ticks read from the encoder at the given sample time. In this case, the block output is the same as in the Reset at each Sample time mode.

Dependencies

To enable this port, set Reset mode to Reset by external signal.

Data Types: single | double | int8 | int16 | int32 | uint8 | uint16 | uint32 | Boolean

Output

expand all

The block outputs the relative change in the position of the rotating motor in ticks. You can find out the direction of rotation of the motor based on the previous and current tick counts and the Reset mode selected. For example, in the No reset mode, with a previous tick count of 30 and current tick count of 20, the motor is moving in a counterclockwise direction.

Data Types: int16

Parameters

expand all

Select your Raspberry Pi hardware board. You can find this information on the target hardware, product packaging, or product documentation.

Select the GPIO pin on the Raspberry Pi hardware board to which the output A of the encoder is connected.

Select the GPIO pin on the Raspberry Pi hardware board to which the output B of the encoder is connected.

The block supports three reset modes.

  • No reset — The block outputs the total tick count read from the encoder.

  • Reset at each Sample time — The block outputs the number of ticks read from the encoder at the given sample time.

  • Reset by external signal — When you set the parameter to this mode, an input port becomes available. In this mode, when the value of the signal at the input port is 0, the block output is the same as in the No reset mode. When the value of the signal at the input port is a nonzero value, the block output is the same as in the Reset at each sample time mode.

Assume that the encoder wheel connected to the hardware has 90 slots, which means that the encoder tick count is 1 for every 4 degrees of rotation. Assume that the block sample time is 1 second and the tick count at time instant T = 0 is 0. This table shows the tick counts that the block outputs in the three modes.

Raspberry Pi reset mode image

  • Between T = 0 and T = 1, assume that the encoder rotates 20 degree clockwise. The output in each mode is:

    • No reset — The output is 20 / 4 = 5

    • Reset at each sample time — Assume that the encoder has rotated 20 degrees at the given sample time, so the output is 20 / 4 = 5

    • Reset by external signal — Assume that the value of the external signal is 0, so the count is calculated as in the No reset mode, and the output is 20 / 4 = 5

  • Between T = 1 and T = 2, assume that the encoder rotates 40 degrees clockwise. The output in each mode is:

    • No reset — In this mode, the block outputs at any time instant is the sum of the previous count and the current count, so the output is 5 + 40 / 4 = 15

    • Reset at each sample time — Assume that the encoder has rotated 40 degrees at the given sample time, so the output is 40 / 4 = 10

    • Reset by external signal — Assume that the value of the external signal is 0, so the count is calculated as in the No reset mode, and the output is 5 + 40 / 4 = 15

  • Between T = 3 and T = 4, assume that the encoder rotates 20 degrees counterclockwise. The output in each mode is:

    • No reset — In this mode, the block output at any time instant is the sum of the previous count and the current count, so the output is 30 – 20 / 4 = 25

    • Reset at each sample time — Assume that the encoder has rotated 20 degree counterclockwise at the given sample time, so the output is – 20 / 4 = – 5

    • Reset by external signal — Assume that the value of the external signal is a nonzero value, so the count is calculated as in the Reset at each sample time mode, and the output is – 20 / 4 = – 5

Enter the time interval in seconds at which the block reads values from the encoder.

Version History

Introduced in R2021a