SENT
Read high-resolution sensor data over Single Edge Nibble Transmission (SENT) protocol
Since R2023b
Libraries:
SoC Blockset Support Package for Infineon AURIX Microcontrollers /
AURIX TC4x
Description
The SENT block reads high-resolution data from sensor and provides 32-bit data output based on SENT (Single Edge Nibble Transmission) protocol (SAE J2716). The output based on SENT protocol is a unidirectional signal from sensor to controller, encoding sensor data information in the form of nibbles (4-bit data), packing 8 nibbles together.
The block also provides the options to enable additional outputs about the Status and Communication nibble, serial data, and the status of data reception.
Ports
Input
DataSel — Data selection based on features or sensors configured
scalar
This input port requests data based on sensor or feature selection configuration in SENT Configuration.
Note
You can provide the input as 1, 2 or 3 if you select SPC Mode parameter as
Feature selection
.You can provide the input as 1, 2, 3 or 4 (based on the number of sensors interfaced on SENT channel) if you select SPC Mode parameter as
Sensor selection
.
Dependencies
To enable this port, set the SENT Protocol as
SPC Mode and select the SPC
Modeparameter as Feature selection
or Sensor selection
.
Data Types: uint8
Output
Data — 32-bit data
scalar
|
vector
The block outputs 32-bit value that represents the sensor data, packing 8 nibbles (4-bit data) together.
Data Types: uint32
Serial-data — 16-bit serial data
scalar
|
vector
The block outputs the 16-bit serial data that represents the sensor data.
Dependencies
To enable this port, select the Serial parameter.
Data Types: uint16
Status & Comm — Status and Communication nibble data (one nibble)
scalar
The block outputs the Status and Communication nibble data sent by the sensor (1st nibble information), which generally provides diagnostic information like fault data, part numbers, and so on.
Dependencies
To enable this port, select the Status and Communication Nibble parameter.
Data Types: uint8
Channel status — Status of read operation over SENT protocol
scalar
The block outputs the status of the data that was read, or the errors that
occurred during the data transfer, as a unit32
scalar
value.
Bit | Status | Description |
---|---|---|
Bit 0 | Receive success | This bit is set at the successfully received end of a frame. If CRC check is enabled, it also indicates successful CRC check. |
Bit 1 | Receive data success | This bit is set when received frame is moved to data register. Both RSI and RDI. |
Bit 2 | Receive buffer overflow | This bit is set when new data is received while older one is still not read from data register. Older data gets overwritten by new data. |
Bit 3 | Transfer data | This bit is set after the trigger condition was detected. Data to be transferred has been moved internally and new value can be written in SPC control register. |
Bit 4 | Transmit buffer underflow | This bit is set after data has been successfully transferred and no new data was written to SPC control register. |
Bit 5 | Frequency range error | This bit is set after a Synchronization / Calibration pulse was received that deviates more than +/- 25% from the nominal value. |
Bit 6 | Frequency drift error | This bit is set after a subsequent Synchronization / Calibration pulse was received that deviates more than 1.5625% from its predecessor. |
Bit 7 | Wrong number of nibbles received | This bit is set if less/more nibbles have been received than expected. |
Bit 8 | Nibbles value out of range | This bit is set if value off Nibble is not in range. It is less than 0 or greater than 15. |
Bit 9 | CRC error | This bit is set when CRC fails. |
Bit 10 | Wrong SC Nibble | This bit is set if Status and Communication nibble shows a start bit in a frame other than frame number nx16. |
Bit 11 | Serial data received | This bit is set after all serial data bits are received using the Status and Communication nibble. |
Bit 12 | Serial data CRC error | This bit is set if the CRC of the serial message fails. |
Bit 13 | Watch dog error | This bit is set if watchdog timer of the channel has expired. |
Dependencies
To enable this port, select the Enable channel status port parameter.
Data Types: uint32
Parameters
Basic
Data format selection — Select data format
None
(default) |
Serial
|
Status and Communication Nibble
Select the data format.
Serial
- In this data format, the block outputs serial data based on the SENT protocol.When you select this option, the block configures the
Serial-data
output port.Status and Communication Nibble
- In this data format, the block provides the Status and Communication nibble data based on the SENT protocol.When you select this option, the block configures the
Status & Comm
output port.
Enable channel status port — Enable output data that specifies data read status and error
off
(default) |
on
Enable output data that specifies data read status and errors (if any) based on bit-wise categorization.
Sample time — Frequency at which block reads the received data
-1
(default) |
scalar
|
vector
Specify in seconds how often the block should read the received data.
When you specify this parameter as -1
, Simulink® determines the best sample time for the block based on the block
context within the model.
Advanced
SENT Protocol — Select the SENT protocol
Standard
(default) |
SPC
Select SENT protocol as standard or short PWM code (SPC) transmission for the channel.
Selection of this parameter as SPC
enables
options in Advanced tab in the SENT Configuration.
SPC Mode — Mode of SPC transmission
Synchronization
(default) | Feature selection
| Sensor selection
Select mode of SPC transmission.
Selection of this parameter enables the related parameters in the SENT Configuration.
Dependencies
To view this parameter, set the SENT Protocol
parameter as SPC Mode
.
Version History
Introduced in R2023b
See Also
MATLAB 命令
您点击的链接对应于以下 MATLAB 命令:
请在 MATLAB 命令行窗口中直接输入以执行命令。Web 浏览器不支持 MATLAB 命令。
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
You can also select a web site from the following list:
How to Get Best Site Performance
Select the China site (in Chinese or English) for best site performance. Other MathWorks country sites are not optimized for visits from your location.
Americas
- América Latina (Español)
- Canada (English)
- United States (English)
Europe
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)