Is it possible to use an NI USB-6002 using the Data Acquisition Toolbox only (error NI Error -200452)?

Question

Roger 2014-9-30

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/156871-is-it-possible-to-use-an-ni-usb-6002-using-the-data-acquisition-toolbox-only-error-ni-error-200452

编辑： Walter Roberson 2015-11-14

I am using R2014a and its Data Acquisition Toolbox. I am able to establish a session, communicate to setup DI/O, Analog Output and Timer, but can not create an Analog Input. The error I get from this is as follows:

Error using Read_Write_NI_daq (line 23)
NI Error -200452:
Specified property is not supported by the device or is not applicable to the task.
Property: DAQmx_AI_Coupling
Channel Name: Dev1/ai0
Task Name: _unnamedTask<95>
Status Code: -200452

My code:

% Read and Write to NI USB-6002
clc
clear
NI_daq = daq.getDevices;
NI_daq_session = daq.createSession('ni');   % create session with the daq
% add analog output channel
% [ch, idx] = addAnalogOutputChannel(NI_daq_session,'Dev1',0:1,'Voltage');
% outputSingleScan(NI_daq_session,[-2.5 3.5]);
% add digital channels
% [ch, idx] = addDigitalChannel(NI_daq_session,'Dev1','port0/line4:7','OutputOnly');
% outputSingleScan(NI_daq_session,[1 0 1 0]);
% add analog input channel
% addAnalogInputChannel(NI_daq_session,'Dev1','ai0','Voltage');
%     NI_daq_session.addAnalogInputChannel('Dev1','ai1','Voltage')
% ch=addAnalogInputChannel(NI_daq_session,'Dev1','ai0', 'Voltage');
[ch, idx] = addAnalogInputChannel(NI_daq_session,'Dev1','ai0','Voltage');
% startForeground
data = inputSingleScan(NI_daq_session);

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Friedrich 2014-10-1

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/156871-is-it-possible-to-use-an-ni-usb-6002-using-the-data-acquisition-toolbox-only-error-ni-error-200452#answer_153483

Hi,

The USB 6002 is not officially supported by Data Acquisition Toolbox. For a list of supported devices see here. Maybe try to upgrade to a nidaqmx version greater than 9.8.x and try again. There were some driver changes on the NI side which might make it possible to use.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Answer 2

Othmane 2014-10-7

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/156871-is-it-possible-to-use-an-ni-usb-6002-using-the-data-acquisition-toolbox-only-error-ni-error-200452#answer_154164

I am having the same problem

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Answer 3

Othmane 2014-10-7

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/156871-is-it-possible-to-use-an-ni-usb-6002-using-the-data-acquisition-toolbox-only-error-ni-error-200452#answer_154165

The AOs work just fine for this 6002 Device using the exact same syntax, but the AIs don't work and I get the same error message as above. I am also using the latest version of the nidaqmx