How to Make a Simulink Scheduler for a Matlab Block Function to run each 40 ms of simulation?

Question

Gianluca Mammone 2022-8-10

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1777310-how-to-make-a-simulink-scheduler-for-a-matlab-block-function-to-run-each-40-ms-of-simulation

编辑： Gianluca Mammone 2022-8-18

Hello, I am trying to make a controller for a system that must run every 40-50 ms. I am having difficulties with Stateflow because if I try to adapt the example given by Mathworks the matlab blocks runs just once.

In the picture you see the controller that I adapted from the example

this is "Edge to Function" block

and this is the simple subsystem called by Call() event

inside the matlab block there is only

j = 0;

for i = 1:10

j = j+1;

end

and here the plot of the output j, as you can see the block is triggered just once

Can you please help me to understand how to call the matlab block every 40 seconds or address me to a good stateflow scheduler tutorial? I haven't been lucky

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Fangjun Jiang 2022-8-10

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1777310-how-to-make-a-simulink-scheduler-for-a-matlab-block-function-to-run-each-40-ms-of-simulation#answer_1024485

Use a Function-call Generator block, specify the sample time. Put the MATLAB Function block inside a triggered subsystem, specify the trigger as Function-call.

3 个评论
显示 1更早的评论隐藏 1更早的评论

Fangjun Jiang 2022-8-18

"triggered system in a loop"?? It sounds too complicated. Please state your task, there might be a better way to construct the model to implement it.

Gianluca Mammone 2022-8-18

编辑：Gianluca Mammone 2022-8-18

My task is to create a controller that runs every 40 Ms. The dynamic differential model of the plant is a matlab function followed by integrators that calculate the state.

This controller every 40 ms is triggered, collect the actual state (the output of the integrator which is the output of the Matlab Function Block), and gives the value of the controlled variable.

The controller is quite heavy (MPC with QP), so I am not too prone to use zero-older hold block

EDIT: I think I solved it, thank you for your patience.

One of the inputs (let's call it dx) of the triggered block was the direct output of the matlab function. Since the matlab function needed the output of the controller to run, there was this data dependency where dx was not initialized or defined.

请先登录，再进行评论。

How to Make a Simulink Scheduler for a Matlab Block Function to run each 40 ms of simulation?

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

3 个评论
显示 1更早的评论隐藏 1更早的评论

更多回答（0 个）

另请参阅

类别

标签

产品

版本

Community Treasure Hunt

How to Make a Simulink Scheduler for a Matlab Block Function to run each 40 ms of simulation?

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

3 个评论 显示 1更早的评论隐藏 1更早的评论

更多回答（0 个）

另请参阅

类别

标签

产品

版本

Community Treasure Hunt

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

3 个评论
显示 1更早的评论隐藏 1更早的评论