how to compute running correlation coefficient

28 次查看（过去 30 天）
Kathleen
Kathleen 2015-4-3
回答： David J. Mack 2017-12-21
Hi, I'd like to calculate a 'running' correlation coefficient of two variables. t seems that my problem is that the corrcoef(x,y) function writes a (2,2)-Matrix but I only wanna save the actual coefficient, i.e. (1,2) or (2,1), into my resuls. How can I do this? Any help is very much appreciated! > > > I've tried the following:
Here some fake data:
x = [1 3 4 8 9 12 13 14 40 30];
y = [2 3 4 7 8 9 13 14 41 32];
window=2; % window size for the correlation coefficient

请先登录，再回答此问题。

回答（3 个）

David J. Mack
David J. Mack 2017-12-21
And again... Have a look at MOVCORR
Greetings, David
the cyclist
the cyclist 2015-4-3
If you have the Statistics Toolbox, you can use the function corr, which will only return the single value of the correlation.
  1 个评论
Kathleen
Kathleen 2015-4-3
Thanks for your reply and help. But the syntax corr cannot be used to facilitate this.

请先登录，再进行评论。

Roger Stafford
Roger Stafford 2015-4-3
编辑：Roger Stafford 2015-4-3
By "running correlation coefficient" I assume you mean you want the correlation computed for each possible length of x and y from 1:1, 1:2, ..., 1:N for some large maximum number N. If N is very large it becomes inefficient to repeatedly compute using 'corrcoef'. Fortunately it is possible to express the correlation in terms of five running sums which can greatly reduce the total computation required. You can see this form in the Wikipedia site
http://en.wikipedia.org/wiki/Correlation_and_dependence
near the end of the first section.
The following code carries out that computation in terms of the Wikipedia formula.
sx = x(1); sy = y(1);
sx2 = x(1)^2; sxy = x(1)*y(1); sy2 = y(1)^2;
c(1) = 1; % Avoid a NaN on the first step
for n = 2:N
sx = sx + x(n);
sy = sy + y(n);
sx2 = sx2 + x(n)^2;
sxy = sxy + x(n)*y(n);
sy2 = sy2 + y(n)^2;
c(n) = (n*sxy-sx*sy)/sqrt((n*sx2-sx^2)*(n*sy2-sy^2));
end
Note that for each step in the loop there are only about twenty operations performed for updating the correlation value c(n), whereas with a large value for N, each step would involve some multiple of n of such operations.
You should not necessarily take the above code literally, but its method may serve to give you a procedure for performing the computation more efficiently for your "running" type situation.
  2 个评论
Kathleen
Kathleen 2015-4-3
Dear Roger,
Thanks for your reply and help! I want to compute the sliding or running window correlation coefficient. I have read related papers, the formula is as following:
t=n,n+1,n+2,n+3，......。 n means the length of silding or running window.
Could you translate this formula into Matlad codes? Any help is very much appreciated! Many many thanks!
Roger Stafford
Roger Stafford 2015-4-3
Just change the way the five "running" sums are generated.
t = 10; % <-- You choose the width of the window
sx = cumsum(x); sx = sx(t+1;end)-sx(1:end-t);
sy = cumsum(y); sy = sy(t+1;end)-sy(1:end-t);
sx2 = cumsum(x.^2); sx2 = sx2(t+1;end)-sx2(1:end-t);
sxy = cumsum(x.*y); sxy = sxy(t+1;end)-sxy(1:end-t);
sy2 = cumsum(y.^2); sy2 = sy2(t+1;end)-sy2(1:end-t);
c = (t*sxy-sx.*sy)./sqrt((t*sx2-sx.^2).*(t*sy2-sy.^2));

请先登录，再进行评论。

类别

在 Help Center 和 File Exchange 中查找有关 Curve Fitting Toolbox 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by