Changing initial conditions of a Simulink model when simulating using a for loop

Question

J AI 2023-5-29

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1975304-changing-initial-conditions-of-a-simulink-model-when-simulating-using-a-for-loop

评论： Paul 2023-6-14

I am trying to run a vehicle simulink model (taken from here) for 5 seconds. When I try running it directly, the response seems to make sense.

However, when I use a for loop to do the same using a for loop (see attached runExample.m), the response is quite different. My assumption is I am not changing the initial conditions after each loop properly. Is there a way to update the initial conditions automatically instead of the way I am doing it, i.e., manually? What other ways could I trye to have the same responses with and without the for loop?

All the relevant files are uploaded. Simply set runDirect in the runExample.m file to true to run without the for loop, otherwise, set it to false.

Thanks in advance for your time. Looking forward to get some solution.

3 个评论
显示 1更早的评论隐藏 1更早的评论

J AI 2023-6-6

Thanks for asking. Let me try to break down:

if runDirect == true

out = sim('DynamicModel',totalTime);

figure()

plot(out.x.data,out.y.data,'b','LineWidth',2)

xlabel('x (m)')

ylabel('y (m)')

else

The above code inside runExample.m runs the simulink model for 5 seconds and produces the following output (blue):

However, what I am trying to do is: instead of running the whole model in one-go, run the model for each time step, i.e., dt = 0.1 s, using for loop by passing the final boundary condition as the initial boundary condition at the end of the loop. This of course requires that all the boundary conditions be updated at the end of the loop, but I am not sure how to identify these boundary conditions in a simulink model. I have manually identified some [x0,y0,yaw0,yaw_rate0,vx0,vy0,volume0,omega0,z0,zdot0], but it seems like these are not sufficient since the output using the for loop is quite different.

In other words, I want to be able to store the boundary conditions at the end of each iteration so that they can be used in the next iteration.

Hope that clarifies the question further. Please let me know if you need any other information.

Thanks in advance!

P.S. I have slightly updated the files. So re-attaching them.

J AI 2023-6-7

在 MATLAB Online 中打开

Here is a very minimal example of what I want but using script (instead of simulink). Here, we just have one boundary condition, y0, and thus changing it in every loop results in perfect match for both the outputs.

% run directly

dt = 0.1;

y0 = 1;

time = 0:dt:5;

[t, y] = ode45(@odeExample, time, y0);

% using for loop

y0 = 1;

tspan = 0:dt/10:dt;

y_loop = y0;

for i = 2:length(time)

[t,y_arr] = ode45(@odeExample, tspan, y0);

y0 = y_arr(end);

y_loop = [y_loop, y0];

end

hold on

plot(time, y, 'r','LineWidth',2);

plot(time, y_loop, 'b--','LineWidth',2);

xlabel('Time');

ylabel('y');

title('Solution of dy/dt = -2y');

legend('Direct','For loop')

function dydt = odeExample(t, y)

dydt = -2 * y;

end

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Paul 2023-6-11

1
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1975304-changing-initial-conditions-of-a-simulink-model-when-simulating-using-a-for-loop#answer_1253674

I think you can do what you want using Model Operating points. Here's a doc page to get started.

Why do you want to do this: instead of running the whole model in one-go, run the model for each time step, i.e., dt = 0.1 s, using for loop by passing the final boundary condition as the initial boundary condition at the end of the loop.

Is there a need to take action at the end of one time step and before starting the simulation for the next time step? Asking because there may be an alternative to accomplish whatever the goal is.

4 个评论
显示 2更早的评论隐藏 2更早的评论

J AI 2023-6-12

在 MATLAB Online 中打开

I believe you are pointing to the right direction. Thanks a lot.

However, according to the doc, when I add the following line to my code:

set_param(DynamicModel, 'SaveFinalState', 'on', 'FinalStateName', 'xfinal', 'SaveFormat', 'Structure with time');

I get the following error:

Warning: Simulink counts the discrete states only for blocks that are outside For Each subsystems in model 'DynamicModel'. 
> In runExample (line 32) 
Warning: Non-scalar data in first argument to set_param is detected.
Only first handle in the matrix is processed. 
> In runExample (line 32) 
Error using runExample
Invalid Simulink object handle

where, line 32 refers to the above. I am not sure how could I solve the subsystem issue. Any idea?

As for your question what I am trying to achieve here:

I am trying to control the vehicle model defined in DynamicModel. Therefore, based on the states at the end of each time-step, i.e., dt=0.1 s, the control input values need to be calculated. But without storing the model operating points, it is not possible to start the simulink simulation from the same energy level at the last time step. Will be glad if you could provide an alternative way to achieve this. I used this technique in my masters except through the script as shown in the example above.

J AI 2023-6-14

"In line 32, what is the value of the variable DynamicModel?": I am not sure what you mean. To my understanding, the simulink model I uploaded has several model operating points, of which I have identified some. Changing those variables manually at the end of each loop manually does not solve my issue. So I was hoping the SaveFinalState option would allow me to do that automatically in the variable xfinal.

"Why not implement the control algorithm in the Simulink model itself?": The control algorithm is coded in Python using its neural network libraries. I am not proficient and lack quite a bit of understanding on the issue of communicating between python and matlab. With simulink, I believe there is another added layer of complexity.

Paul 2023-6-14

在 MATLAB Online 中打开

In this line

set_param(DynamicModel, 'SaveFinalState', 'on', 'FinalStateName', 'xfinal', 'SaveFormat', 'Structure with time')

DynamicModel is not in quotes as would be typical in set_param usage. Are you sure it shouldn't be

set_param('DynamicModel', 'SaveFinalState', 'on', 'FinalStateName', 'xfinal', 'SaveFormat', 'Structure with time')

请先登录，再进行评论。

Changing initial conditions of a Simulink model when simulating using a for loop

3 个评论
显示 1更早的评论隐藏 1更早的评论

回答（1 个）

4 个评论
显示 2更早的评论隐藏 2更早的评论

另请参阅

类别

标签

产品

版本

Community Treasure Hunt

Changing initial conditions of a Simulink model when simulating using a for loop

3 个评论 显示 1更早的评论隐藏 1更早的评论

回答（1 个）

4 个评论 显示 2更早的评论隐藏 2更早的评论

另请参阅

类别

标签

产品

版本

Community Treasure Hunt

3 个评论
显示 1更早的评论隐藏 1更早的评论

4 个评论
显示 2更早的评论隐藏 2更早的评论