Image Analysis: measuring cusping and roughness

Question

Shan Kapoor 2011-10-30

1
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/19831-image-analysis-measuring-cusping-and-roughness

Dear All,

I am looking for a solution for the following problem. Please refer the image below.

https://picasaweb.google.com/116243239493929305987/ImageAnalysis#5654551982275072578

A straight line was drawn though the mid-axis each of the black laths as shown. Lines perpendicular to this axial line were drawn to the peaks and valleys of the black laths.The height difference between peaks and valleys is defined as the roughness. The spacing between the valleys is defined as a measure of cusp spacing. Right now I am doing it manually and its subjective to lots of errors. Please suggest a way by which I can automate this process. ( ie findout the hight difference and spacing between an area of selected peaks and vallieys.

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

Image Analyst 2011-10-31

Funny. Two authors in one night posting the same questions as if for the first time when there had already been a discussion of the same topic weeks earlier:

http://www.mathworks.com/matlabcentral/answers/16296-image-analysis-finding-the-cusp-spacing

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Sven 2011-10-31

1
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/19831-image-analysis-measuring-cusping-and-roughness#answer_26215

在 MATLAB Online 中打开

Here's how I would approach it:

% Read the image and convert to BW mask of peaks
I_orig = imread('cusp_micro.jpg');
I = rgb2gray(I_orig);
BW_peaks = im2bw(I);
% How far is every non-peak pixel from its nearest peak?
distFromPeaks = bwdist(BW_peaks);
% Let's only choose pixels further from a peak than any of its neighbours
maxDistsMask = imregionalmax(distFromPeaks);
[trI,trJ] = find(maxDistsMask);
trVals = I(maxDistsMask);
tr2pkDists = distFromPeaks(maxDistsMask);
% Now loop over each trough and find the image intensity of its nearest
% peak (add 5 pixels padding so we choose the max from a few nearby peaks)
pkInds = find(BW_peaks);
[pkI,pkJ] = ind2sub(size(BW_peaks),pkInds);
trPartnerPkVals = zeros(size(trI));
for i = 1:length(trI)
    tr2allPkDists = sqrt((pkI-trI(i)).^2 + (pkJ-trJ(i)).^2);
    withinRangeMask = tr2allPkDists < (tr2pkDists(i) + 5);
    trPartnerPkVals(i) = max(I(pkInds(withinRangeMask)));
end
% Display what we've got:
I_norm = double(I)/double(max(I(:)));
figure, imshow(cat(3,I_norm,max(BW_peaks, I_norm),I_norm)), hold on
plot(trJ,trI,'m.')
% Now if we look at all of the maxdists in the image, how far away from
% peaks are they?
figure, plot(sort(tr2pkDists)), title 'Distribution of cusp spacing'
figure, plot(sort(trPartnerPkVals - double(I(maxDistsMask))))
title 'Distribution of roughness'

So the largest trough2pk distance (or cusp spacing) is around 40 pixels. Notice of course that there are a range of pk2trough values depending on where you look in the image, likewise measures of roughness. You may need a scheme to select maximum cusp spacing or roughness within an X-pixel radius of an area you're interested in, or something similar.

Thanks, Sven.

5 个评论
显示 3更早的评论隐藏 3更早的评论

Shan Kapoor 2011-11-1

Well, The long laths with small valleys is an issue. I must consider a piece with a roundness, aspect ratio or so.

Here is an analysis of a processed image

https://picasaweb.google.com/116849636652679518537/Example2#5669919510020063826

https://picasaweb.google.com/116849636652679518537/Example2#5669919570387963842

We can see that there are four subgrains here indicated by a,b,c and d. If I exclude a and d and measure the cusp spacing ( or subgrain length), I must get the length between 2-4 and 4-6. My roughness values are difference between 1e-2f,2f-3g,3g-4h,4h-5i etc...

Manual measurements of the Cusp spacings gives me 104 pixels (2-4) and 128 pixels (4-6). But the matlab plot does not give those values. For roughness, the plot gives me a single value of 255, what I was looking for was the above mentioned for roughness. that certainly changes from one after the other.

We can see that point 6 is not detected by the algorithm. If we watershed on the original image, distance between two cut lines joining the ultimate point between them can be cusp spacing. difference between one of the cut lines and a perpendicular from the ultimate point to the edge can be the roughness value.

Shan Kapoor 2011-12-30

dear Sven,

Can I further join the points in each laths and draw perpendiculars from the line to the lath edges and measure their lengths based on a pixels distance we specify ?? so that the expected output should look like this

https://picasaweb.google.com/116243239493929305987/December292011#5691497323268999938

My idea is to just describe the laths roughness based on the distribution of lengths of perpendiculars based on the width we specify. At a particular width, there will be a nice distribution of long and short lines and I will be able to manipulate it further.

Shan Kapoor 2012-1-12

dear Sven

could you please guide me understanding this portion of the code ?

% Now loop over each trough and find the image intensity of its nearest

% peak (add 5 pixels padding so we choose the max from a few nearby peaks)

pkInds = find(BW_peaks);

[pkI,pkJ] = ind2sub(size(BW_peaks),pkInds);

trPartnerPkVals = zeros(size(trI));

for i = 1:length(trI)

tr2allPkDists = sqrt((pkI-trI(i)).^2 + (pkJ-trJ(i)).^2);

withinRangeMask = tr2allPkDists < (tr2pkDists(i) + 5);

trPartnerPkVals(i) = max(I(pkInds(withinRangeMask)));

end

what exactly is [pkI,pkJ] ?? and what does it do with the rest of the code ? when I tried plotting [pkI,pkJ], it filled everywhere other than the black pixels...

thanks in advance,

Shanoob

请先登录，再进行评论。

Image Analysis: measuring cusping and roughness

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

采纳的回答

5 个评论
显示 3更早的评论隐藏 3更早的评论

更多回答（0 个）

另请参阅

类别

标签

Community Treasure Hunt

Image Analysis: measuring cusping and roughness

1 个评论 显示 -1更早的评论隐藏 -1更早的评论

采纳的回答

5 个评论 显示 3更早的评论隐藏 3更早的评论

更多回答（0 个）

另请参阅

类别

标签

Community Treasure Hunt

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

5 个评论
显示 3更早的评论隐藏 3更早的评论