PV module simulation

21 次查看（过去 30 天）
Nuno
Nuno 2011-3-8
回答： SINDHUJA D 2019-10-13
Which toolbox i will be used in PV module simulation?
  2 个评论
Andrew Alkiviades
Andrew Alkiviades 2012-1-23
Hi Nuno,
Are you using the single diode equivalent circuit?
Do you have the series and shunt resistances for the module you are looking at?
Muhammad Talha
Muhammad Talha 2019-10-7
Hello guys i need help regarding my final year project i mathematically model a PV cell where output is Current and voltage so i can get easily output waveform accurately but i dont know how can i convert this module to PV array model like in simulink Built in block where we get + or - sign and how i can i attached boost converter with my model

请先登录，再进行评论。

请先登录，再回答此问题。

采纳的回答

Arnaud Miege
Arnaud Miege 2011-3-8
It depends on what you want to. If you want to model the photovoltaic cell, then you'll probably need Simscape and SimElectronics, which has a Solar Cell block. If you are interested in modelling the connection to the grid and the DC/AC conversion, then you'll probably need SimPowerSystems. have a look at the webinar Model-Based Design for Solar Power Systems for more information.
HTH,
Arnaud
  4 个评论
显示 2更早的评论
Hossein
Hossein 2011-12-27
Hi Arnaud,
as I found we can connect simscape and simpower together ,So there is another way to simulation,which is mix both of them...
for example using Solar Cell block from simscape and connect to DC/DC converter from simpower ...
Is it right????
Mohan
Mohan 2015-3-1
I need some help in grid connection of inverter. i have attached a model, in which the current from inverter + grid = load. they r not in phase bt are getting added up...,,, if there s a mistake n PLL pls help me crct it

请先登录，再进行评论。

更多回答（8 个）

Ambika
Ambika 2012-1-27
hi,am also working on MPPT.. for the PV module u can go for either coding or modelling using blocks...if u r intrested in modelling using blocks then u can easily do it with the help of commonly used blocks,sinks,sources,math operations in simulink otherwise u can go for simpower system ,there u can directly take diode,sources,MOSFET etc..
  1 个评论
Hossein
Hossein 2012-1-30
hi Ambika,
Do you have any experience about connecting simpower and simscape?
I mean connecting the solar cell block in simscape to DC-DC converter in simpower ???

请先登录，再进行评论。

Hossein
Hossein 2011-8-27
How can I find "Model-Based Design for Solar Power Systems" Webinar???????????????
  3 个评论
显示 1更早的评论
Sai001 Cheguri
Sai001 Cheguri 2011-10-10
How can I find out the values in temperature tab of the solar cell,(temperature exponents of saturation current(Is),series and parallel resistances(Rs & Rp) and what is the first order temperature coefficient?
shrik kader
shrik kader 2017-5-28
What are these two links? when I click on them it turn me back to this comment.

请先登录，再进行评论。

Hossein
Hossein 2011-10-31
Thank you very much Lucas,I have looked to this webinar so much,you help me with webinar so much...
herve manara
herve manara 2011-11-9
Hi Folks,
I am working on project that is to develop a small-scale solar system (solar harvester) to charge rechargerable batteries of a Wireless Sensor Devices/Nodes). I need to design and simulate a system that work with MPPT but I have no idea on how to implement MPPT to drive the gate pin of MOSFET as seen on the video link above.
I look up to your propositon.
Hossein
Hossein 2011-11-16
Hi Menara, The main duty and output of MPPT is generate duty cycle for DC/DC converter or DC/AC inverter ,so you can refer the duty cycle to MOSFET to adjust the voltage of Photovoltaic panel to find the knee(maximum power point) of I-V curve,becuse in this point you have the maximum area under I-V curve and conclude the maximum power...
Alfred Baams
Alfred Baams 2017-3-30
what is appropriate device or components to be use to stabilises the pv array model before connection to dc boost converter?
  1 个评论
Tony Castillo
Tony Castillo 2018-2-13
I think you can gain stabilization in that point with a simple Capacitor. Did you do it?

请先登录，再进行评论。

SHOUTRIK DAS
SHOUTRIK DAS 2019-3-9
Hi, I"m designing a MPPT system for a PV module.
I have designed the PV module and used the current output from the pv module subsystem as the control signal for a controlled current source.
Before connecting the controlled current source the output from the PV module is a smooth curve.
After connecting the Current source it looks like this.
How to solve this issue??
Capture02.JPG
SINDHUJA D
SINDHUJA D 2019-10-13
Hi,
I am designing a Incremental Conductance MPPT based solar panel both series and parallel connection. I faced a problem while connecting a solar 4 strings are in parallel connection. In parallel Connection current value not added .
Is there any solution.

类别

在 Help Center 和 File Exchange 中查找有关 Sources 的更多信息

标签

产品

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by