How can I get the code execution tome of the model in simulink? (for the code generation of the C2000 processors)

Question

JIANWEI 2017-2-24

1
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/326670-how-can-i-get-the-code-execution-tome-of-the-model-in-simulink-for-the-code-generation-of-the-c200

评论： BD 2017-12-3

I want to know what is the execution time of my model in simulink. I need to set a proper sampling time for the code generation for C2000 processors.

Thanks.

2 个评论
显示无隐藏无

Sudarshan Kolar 2017-2-27

在 MATLAB Online 中打开

To determine the execution time of a model you can use the following command:

tic
sim('myModel');
toc

or you can also use Simulink profiler .

Hope that helps.

JIANWEI 2017-2-28

tic and toc are used together to measure the elapsed time, not the execution time.

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Antonin 2017-3-9

1
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/326670-how-can-i-get-the-code-execution-tome-of-the-model-in-simulink-for-the-code-generation-of-the-c200#answer_257995

Hi JIANWEI,

Here are 2 techniques that will help you profile the execution time of the generated code on the TI C2000 processors:

In R2017a, we introduced multitasking profiling, which will allow you to measure and visualize execution time and preemptions for the different synchronous rates in your model. Check the Real-Time Code Execution Profiling Example to learn more about this technique.
In PIL mode, you can enable profiling and measure the execution time of your generated code. The Code Verification and Validation with PIL Example will show you how to run in PIL on the TI C2000 devices, while the "Code Verification and Validation with PIL" chapter of the documentation will explain you how to enable profiling with PIL.

I hope this helps,

Good luck!

Antonin.

5 个评论
显示 3更早的评论隐藏 3更早的评论

Antonin 2017-3-13

Hi JIANWEI,

1) The multitasking profiling tool will measure tasks that may be preempted. The "Average Turnaround Time" includes the code execution time and the preemption time while "code execution time" only includes the code execution time in this particular task. If there is no preemption, the two measurements should be equal.

2) In the configuration parameters of the model, go to "Hardware Implementation". You should have a TI C2000 board selected for "Hardware Board". In the "Target Hardware Resources" go to "Execution profiling", this is where you can find the "Number of profiling samples to collect". This will decide how much memory you want to allocate on the Hardware to collect samples for profiling. Profiling starts on the Hardware when the program starts and stops when this buffer is full, so the bigger the buffer is, the more profiling data you will have. Increasing the "Number of profiling samples to collect" will increase the buffer and allow you to measure events that may not be happening at startup.

3) If the execution time is larger than the sample time, you are in an overrun situation which is not good. You want to keep the execution time below the sample time to make sure that you are fully in control of the behavior of your program. For your information, in case of an overrun, our scheduler will skip the next instance of the task. For example if a task is scheduled at 50µs and constantly takes 65µs to execute, you will see this task scheduled at 100µs as we will always skip one execution every cycle. If the task takes 125µs to execute, it will run every 150µs as we will skip twice every cycle, and so on... Better to make sure that you are in control of the sample time and you don't have overruns.

I hope it helps,

Good luck,

Antonin.

JIANWEI 2017-3-14

Hi Antonin,

Thank you very much. These are quite helpful.

Jianwei

BD 2017-12-3

Hi Antonin,

1. Is the execution profile is for code running in hardware or for simulation in simulink environment?

2. If the execution profile is collected from hardware, through which interface (serial, can etc...) the data is collected from hardware.

请先登录，再进行评论。

Answer 2

Manex Barrenetxea 2017-10-27

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/326670-how-can-i-get-the-code-execution-tome-of-the-model-in-simulink-for-the-code-generation-of-the-c200#answer_288089

在 MATLAB Online 中打开

Dear Antonin,

We have tried to measure and visualize execution time and preemptions for the different synchronous rates in our model following your recommendation. However, the following error arose while compiling:

 *The parameter ExecutionProfileBufferLen is not defined for selected hardware board.

We are trying to measure the execution times of the F28335 board. Could you clarify us which could be the root of the error we are having?

Thank you in advance and best regards,

Manex.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

How can I get the code execution tome of the model in simulink? (for the code generation of the C2000 processors)

2 个评论
显示无隐藏无

采纳的回答

5 个评论
显示 3更早的评论隐藏 3更早的评论

更多回答（1 个）

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

另请参阅

类别

标签

Community Treasure Hunt

How can I get the code execution tome of the model in simulink? (for the code generation of the C2000 processors)

2 个评论 显示 无隐藏 无

采纳的回答

5 个评论 显示 3更早的评论隐藏 3更早的评论

更多回答（1 个）

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

另请参阅

类别

标签

Community Treasure Hunt

2 个评论
显示无隐藏无

5 个评论
显示 3更早的评论隐藏 3更早的评论

0 个评论
显示 -2更早的评论隐藏 -2更早的评论