Code that makes matlab jumping loops without fininishing the remaining iterations.

1 次查看（过去 30 天）
BdS
BdS 2019-4-3
评论： BdS 2019-4-10
Hi,
I have got the following 2 loops:
for d=1:nDates %loop over rebdates
for r=1:nRebDates
ind=ismember(PortMembers,rawPortData{d}.PORTFOLIO_MPOSITION{1}(:,1));
PortPositions(d,ind)=cell2mat(rawPortData{r}.PORTFOLIO_MPOSITION{1}(:,2));
end
end
I would like that everytime when one iteration from loop r=r:nRebDates is concluded matlab jumps directly to the first loop d=1:nDates instead of first complete all iterations in loop r=r:nRebDates.
(break does not work as I do want that iteration r=r:nRebDates continues but only after matlab goes through d=1:nDates for a 2nd,3th, 4th... time)
(continue does not work as well as I do want a second iteration of r=r:nRebDates but only after matlab goes to the first loop d=1:nDates)
--> actually is as when I would tell Matlab: after the code line PortPositions(d,ind)=cell2mat(rawPortData{r}.PORTFOLIO_MPOSITION{1}(:,2)); go to d=1:nDates
Do you have any hints?
Thank you in advance.

请先登录，再回答此问题。

回答（2 个）

Bob Thompson
Bob Thompson 2019-4-3
I'm not entirely sure I understand what you're asking for, but it seems like you want to run all iterations of the d loop with the first r value before proceeding to the second r value.
If this is the case, then why don't you just reverse the order of the two loops?
for r=1:nRebDates
for d=1:nDates %loop over rebdates
ind=ismember(PortMembers,rawPortData{d}.PORTFOLIO_MPOSITION{1}(:,1));
PortPositions(d,ind)=cell2mat(rawPortData{r}.PORTFOLIO_MPOSITION{1}(:,2));
end
end
  2 个评论
Bob Thompson
Bob Thompson 2019-4-9
Per your other comments, it sounds like you're just trying to loop through both sets of values at once. To do that you can just use one loop.
r = 1:nRebDates;
d = 1:nDates;
for i = 1:length(r);
ind=ismember(PortMembers,rawPortData{d(i)}.PORTFOLIO_MPOSITION{1}(:,1));
PortPositions(d(i),ind)=cell2mat(rawPortData{r(i)}.PORTFOLIO_MPOSITION{1}(:,2));
end
This will run into problems if your r and d values are of different sizes, but otherwise it should work fine.

请先登录，再进行评论。

BdS
BdS 2019-4-4
Thank you for your answer. I wasn't clear.
Here is the procedure I woul like:
1) First iteration r
2) First iteration d, excecute code (ind=...; PortPositions...)
3) JUMP to SECOND iteration r
4) go on to SECOND iteration d, excecute code...
5) JUMP to THIRD iteration r
6) go on to THIRD iteration d
...(and so on)
I hope that I was clear this time. I think that these kind of questions arrive a lot... specially for programmers who write codes in other programs . (for which go to command exists)
  1 个评论
BdS
BdS 2019-4-8
In the meantime I was able to solve this question...
However, I would like that someone from matlab takes this question and gives me/us/=matlab users some powerful solutions as I think that this kind of questions arise by other users.
thanks in advance.

请先登录，再进行评论。

类别

在 Help Center 和 File Exchange 中查找有关 Loops and Conditional Statements 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by