Help with looping problem

1 次查看（过去 30 天）
Tom
Tom 2012-10-23
Here I am defining x and y coordinates of rays vertically approaching a boundary (currently sin(x))
x = 0:0.1:pi
rx1 = [x(1) x(1)] % x-coordinates, incoming ray 1
ry1 = [y0 sin(x(1))] % y-coordinates, incoming ray 1
rx2 = [x(2) x(2)] % x-coordinates, incoming ray 2
ry2 = [y0 sin(x(2))] % y-coordinates, incoming ray 2
rx3 = [x(3) x(3)] % x-coordinates, incoming ray 3
ry3 = [y0 sin(x(3))] % y-coordinates, incoming ray 3
and so on for the length of vector (x) = 32
Clearly this isn't a good way to write the program. The alternative approach I have tried to use is the following:
i = 1
for i = 1:length(x)
rx(i) = [x(i) x(i)]
ry(i) = [y0 sin(x(i))]
end
Which returns the error:
In an assignment A(I) = B, the number of elements in B and I must be the same.
So clearly this isn't the way to achieve what I was trying to do. I would greatly appreciate if someone could help me resolve this, as I have been stuck on it for some time.

请先登录，再回答此问题。

采纳的回答

Matt Fig
Matt Fig 2012-10-23
Why would you want to create 64 variables like that? What a mess it would be to deal with in further steps. Perhaps two cell arrays could get the job done:
for ii = 1:length(x)
rx{ii} = [x(ii) x(ii)]; % rx is a cell array.
ry{ii} = [y0 sin(x(ii))];
end
Now the really important question is why do you need to do this at all? What is your next step that requires you to have these arrays as individuals, rather than just using x and sin(x)?
  6 个评论
显示 4更早的评论
Tom
Tom 2012-10-23
I haven't encountered this 'line' parameter yet. How come it is plotted without even being asked?
Matt Fig
Matt Fig 2012-10-23
LINE is not a parameter, it is a function.
help line

请先登录，再进行评论。

更多回答（3 个）

Matt Kindig
Matt Kindig 2012-10-23
编辑：Matt Kindig 2012-10-23
I'm not entirely clear what you want, but I think this will do the trick:
x = (0:0.1:pi)';
rx = [x, x];
ry = [ repmat(y0, size(x)), sin(x)];
This implements the vector as specified in the for loop you have shown, which is the preferred way to specify matrix data in Matlab (not creating variables for each line, as your rx1, rx2, etc. example shows).
  1 个评论
Tom
Tom 2012-10-23
编辑：Walter Roberson 2012-10-23
Thanks for the swift response!
That didn't seem to work, perhaps it would make my problem clearer if you run the following:
x = 0:0.1:pi;
y = sin(x);
plot(x,y,'k-')
hold on
rx1 = [x(1) x(1)]
ry1 = [-1 sin(x(1))]
rx2 = [x(2) x(2)]
ry2 = [-1 sin(x(2))]
rx3 = [x(3) x(3)]
ry3 = [-1 sin(x(3))]
plot(rx1,ry1,rx2,ry2,rx3,ry3)
This is what I am trying to achieve (although I have only shown the first 3 vertical lines).
My inexperienced attempt to achieve this with a For loop goes:
for i = 1:length(x)
rx(i) = [x(i) x(i)]
ry(i) = [y0 sin(x(i))]
end
Which returns the error shown above, making clear I'm going completely wrong. Any idea what I should be doing?

请先登录，再进行评论。

Walter Roberson
Walter Roberson 2012-10-23
Azzi Abdelmalek
Azzi Abdelmalek 2012-10-23
y0=1
x = 0:0.1:pi
n=length(x);
eval(sprintf('rx%d=[x(%d) x(%d)],',repmat((1:n),3,1)))
eval(sprintf('ry%d=[y0 sin(x(%d))],',repmat((1:n),2,1)))

类别

在 Help Center 和 File Exchange 中查找有关 Discrete Data Plots 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by