Updating simulink block parameter as the simulation runs.

Question

computer12345 2020-7-6

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/560558-updating-simulink-block-parameter-as-the-simulation-runs

评论： computer12345 2020-7-8

Hello!

I'm new to Matlab and I'm wondering if this is possible.

I have a custom block with a mask that takes in 3 user-input parameters. One of the parameters is frequency and I want to vary the frequency with time while the simulation is running. I looked all over the internet and I found a suggestion to replace the frequency parameter with a workspace variable array, with the array setup as [time1 value1;time2 value2; time3 value3....]. I tried this, but I got an error saying that the there was an issue with the blocks in the subsystem reading the arrays properly. I placed this code into the InitFnc callback.

Am I doing going about this correctly? If so, what do I modify to ensure that the frequency input ports are correctly reading an array input?

If not, is there a different way I can go about changing the frequency with time? I am trying to do everything using a script, rather than including blocks like time steps since the block is masked.

Thanks!

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Fangjun Jiang 2020-7-7

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/560558-updating-simulink-block-parameter-as-the-simulation-runs#answer_462302

在 MATLAB Online 中打开

setting array value as [time1 value1;time2 value2; time3 value3....] works for signal, not for parameters. Use this approach instead

set_param(YourModel, 'SimulationCommand', 'pause');
set_param(YourBlock, parameter, value);
set_param(YourModel, 'SimulationCommand', 'continue');

5 个评论
显示 3更早的评论隐藏 3更早的评论

Fangjun Jiang 2020-7-7

If the frequency needs to be changed several times during a simulation, it is better to make it a signal rather than a parameter. Then you can define F=[time1 value1;time2 value2; time3 value3....] in base workspace and use a "From Workspace" block in your model and specify the data as F.

But that will require you to change your masked subsystem, remove the mask parameter, change it to be an Inport and adjust the blocks inside.

If you can't do that, then here is an alternative.

In your model, add a Clock block and compare (>=) its output to a Constant block with value as time1. The comparision output feeds to an Assertion block, wihch specifies a callback PauseFCN.

When simulation runs to time1, the Assertion will trig the callback PauseFCN, in which you use the above code to

Pause simulation
Change the masked frequency parameter value
Change the Constant block value from time1 to time2
Continue the simulaiton

This way, you can add as many points as you want for the frequency changes. Somewhere in PauseFCN, you need to have some logic to Stop the simulation.

Fangjun Jiang 2020-7-8

It has nothing to do with other functions. The Assertion block is calling PauseFcn, so you have to have a .m script called PauseFcn.m in your MATLAB path.

computer12345 2020-7-8

ohhh I see. I thought that part could link straight to the callback functions associated with the model. Thanks for your help!

请先登录，再进行评论。

Updating simulink block parameter as the simulation runs.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

5 个评论
显示 3更早的评论隐藏 3更早的评论

更多回答（0 个）

另请参阅

类别

标签

产品

版本

Community Treasure Hunt

Updating simulink block parameter as the simulation runs.

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

5 个评论 显示 3更早的评论隐藏 3更早的评论

更多回答（0 个）

另请参阅

类别

标签

产品

版本

Community Treasure Hunt

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

5 个评论
显示 3更早的评论隐藏 3更早的评论