How to modify this script

1 次查看（过去 30 天）
FG
FG 2020-9-8
编辑： Walter Roberson 2020-9-9
I have an M file as shown in the figure. What I want to do is; Instead of naming the cases like: 1111, 1112,1113...3452, 3453, 3454 I want to name them according to the states they are in like:
Case 1111 should be; Power Factor=0.95, PL=14500, FG=500, Angle=0, Nt=1
Case 1112 should be; Power Factor=0.95, PL=14500, FG=500, Angle=0, Nt=2
.
.
.
Would be pleased if you could help me about it.. Thnx
-----------------------------------------------------------------------------------
Q=[atan(18.19) atan(25.84) atan(31.78)];
P=[14500 10000 5000 500];
Ang=[0 10 20 30 40];
NT=[1 2 5 10];
for m=1:length(Q)
QM=Q(m)
for i=1:length(P)
PL=P(i);QL=QM*PL;FG=15000-P(i);
for k=1:length(Ang)
Ang_A=Ang(k);
Ang_B=Ang(k);
Ang_C=Ang(k);
for l=1:length(NT)
Nt=NT(l);
sim('islanding_UW_New_Loads_Fasilali_oran_SonTHD_Deneme')
t=harm_ratio.time;
HV3=harm_ratio.signals(1).values;
HV5=harm_ratio.signals(2).values;
HV7=harm_ratio.signals(3).values;
thd=THD.signals(1).values;
c=sprintf('Case%d%d%d%d',[m,i,k,l])
save(c)
end
end
end
end
  3 个评论
显示 1更早的评论
Walter Roberson
Walter Roberson 2020-9-9
Which variable corresponds to Power factor? I do not seem to find any 0.95 or anything reasonably close in your computations.
PL appears to be variable PL
FG apppears to be variable FG
Angle is ambiguous as to whether it is ANG_A, ANG_B, or ANG_C. All three are set to the same value in the code, so it is not obvious why you have three separate variables, and the differences between them might be important later, perhaps.
Nt appears to be variable Nt
FG
FG 2020-9-9
Q=[atan(18.19) atan(25.84) atan(31.78)] is for Power Factor and cause system is three phase, Angles are Ang_C, Ang_B and Ang_C.. I just want to name the cases according to these criteria istead of 1111, 1112 etc..

请先登录，再进行评论。

请先登录，再回答此问题。

采纳的回答

Walter Roberson
Walter Roberson 2020-9-9
编辑：Walter Roberson 2020-9-9
c = sprintf('Power Factor=%.2f, PL=%g, FG=%g, Angle=%g, Nt=%g.mat', QM, PL, FG, Ang_A, Nt);
It is not clear that having a 54 character filename is desireable ?
Your Q values are 1.51587634897992 1.53211593878758 1.53934037485646 which do not look anything like 0.95 to me.
I used %.2f in the format, which will round to 2 decimal places. For your Q values that will be 1.52 1.53 and 1.54 . It looks to me as if you might be advised to use at least one more decimal place.
Note: Unless you used formats with particular width and leading 0 filling, like %05.2f then your files will not sort in numeric order. For example, 'Power Factor=10.7' sorts before 'Power Factor=2.9'
  1 个评论
FG
FG 2020-9-9
Thank you.. I understand what you mean and you got it done ! Problem solved, thanx again..

请先登录，再进行评论。

更多回答（0 个）

类别

在 Help Center 和 File Exchange 中查找有关 Waveform Generation 的更多信息

标签

产品


版本

R2020a

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by