How to perform Hot Spot Detection ?

3 次查看（过去 30 天）
Syed Muhammad Ali Minhal
评论： Syed Muhammad Ali Minhal 2021-1-30
HI,
what is the equivalent code to be used in App Designer, for the below .m file ?
Thanks
%% Calculate Object Properties Using Pixel Values of Grayscale Image
ti = imread('ti2.jpg');
sc = regionprops('ti2erode.png','ti2rgb.png',{'Centroid','WeightedCentroid'});
figure()
subplot(1,3,1)
imshow(ti)
title('Weighted (red) and Unweighted (blue) Centroids');
hold on
numObj = numel(sc);
for k = 1 : numObj
plot(sc(k).WeightedCentroid(1), sc(k).WeightedCentroid(2), 'r*')
plot(sc(k).Centroid(1), sc(k).Centroid(2), 'bo')
end
hold off

请先登录，再回答此问题。

采纳的回答

Mario Malic
Mario Malic 2021-1-30
There's no equivalent code in AppDesigner, if you just open it and do few examples there, you'll figure out what to do. I made some changes to your code, as this is most likely how it'll look like in App Designer, excluding these first two lines.
uiFig = uifigure;
uiAxes = uiaxes('Parent', uiFig)
%% Calculate Object Properties Using Pixel Values of Grayscale Image
ti = imread('ti2.jpg');
sc = regionprops('ti2erode.png','ti2rgb.png',{'Centroid','WeightedCentroid'});
imshow(ti, 'Parent', uiAxes)
title(uiAxes, 'Weighted (red) and Unweighted (blue) Centroids');
hold(uiAxes, 'on')
numObj = numel(sc);
for k = 1 : numObj
plot(uiAxes, sc(k).WeightedCentroid(1), sc(k).WeightedCentroid(2), 'r*')
plot(uiAxes, sc(k).Centroid(1), sc(k).Centroid(2), 'bo')
end
hold off
  1 个评论
Syed Muhammad Ali Minhal
Syed Muhammad Ali Minhal 2021-1-30
Thankyou @Mario Malic, you were right. By the end of the day I was able to figure out what was missing.
Also I was trying to plot in the UIImage instead of the UIAxes
thanks again
Ihsd = imshow(app.ti, 'Parent', app.UIAxes_4, ...
'XData', [1 app.UIAxes_4.Position(3)], ...
'YData', [1 app.UIAxes_4.Position(4)]);
hold(app.UIAxes_4, 'on')
app.alpha = imread("ti2erode.png"); %binary imaage
app.bravo = imread("ti2rgb.png"); % gray scale image
app.sc = regionprops(app.alpha,app.bravo,{'Centroid','WeightedCentroid'});
app.numObj = numel(app.sc);
for k = 1 : app.numObj
plot(app.UIAxes_4, app.sc(k).WeightedCentroid(1), app.sc(k).WeightedCentroid(2), 'r*');
plot(app.UIAxes_4, app.sc(k).Centroid(1), app.sc(k).Centroid(2), 'bo');
end

请先登录，再进行评论。

更多回答（0 个）

类别

在 Help Center 和 File Exchange 中查找有关 Image Preview and Device Configuration 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by