daq process usb-6008

2 次查看（过去 30 天）

mado 2013-8-18

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/85010-daq-process-usb-6008

how to acquire data from this code to process it in another operation in realtime

    % get connected devices
   d = daq.getDevices
   %create session 
    s = daq.createSession('ni')
    %add analog channel  s.addAnalogInputChannel('ID',channel num, 'measurement type')
   s.addAnalogInputChannel('Dev1',0, 'Voltage')
      % set rate of scan  4 scans/second ,  run for 3 seconds
   s.Rate=1000;
   s.DurationInSeconds=30;
v= s.Channels(1);
set(v)
%_____________________________
v.TerminalConfig = ' Differential';
v.Coupling = ' DC';
%start continuous aquisition and plot
h = s.addlistener('DataAvailable', @(src,event) plot(event.TimeStamps, event.Data/.001));
s.NotifyWhenDataAvailableExceeds = 200;
s.startBackground()

回答（2 个）

Walter Roberson 2013-8-18

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/85010-daq-process-usb-6008#answer_94522

在 MATLAB Online 中打开

The line

h = s.addlistener('DataAvailable', @(src,event) plot(event.TimeStamps, event.Data/.001));

creates the (anonymous) callback function that will be called when data is available; in this case the data is plotted. You would change that line to do whatever processing you needed.

17 个评论
显示 15更早的评论隐藏 15更早的评论

mado 2013-8-21

编辑：Walter Roberson 2013-8-21

在 MATLAB Online 中打开

just i changed differential to SingleEnded

    %%get connected devices
   d = daq.getDevices
   %create session 
    s = daq.createSession('ni')
    %add analog channel  s.addAnalogInputChannel('ID',channel num, 'measurement type')
    s.addAnalogInputChannel('Dev1',0, 'Voltage')
% set rate of scan  4 scans/second ,  run for 3 seconds
 s.Rate=1000;
 s.DurationInSeconds=30;
v= s.Channels(1);
set(v)
%_____________________________
v.TerminalConfig = ' SingleEnded';
v.Coupling = ' DC';
%start continuous aquisition and plot
h = s.addlistener('DataAvailable', @(src,event) plot(event.TimeStamps, event.Data));
s.NotifyWhenDataAvailableExceeds = 200;
s.startBackground()
 s.wait()
delete (h)
h = s.addlistener('DataAvailable', @storedata);s.NotifyWhenDataAvailableExceeds = 200;
s.startBackground()
global matrix_index
global matrix_data
matrix_data(1:matrix_index)

Walter Roberson 2013-8-21

As complete speculation: is it possible that you need channel 1 instead of channel 0 for your single ended measurement ?

请先登录，再进行评论。

mado 2013-8-21

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/85010-daq-process-usb-6008#answer_94759

I need to use both of channel 0 and 1 , will it make a difference ?

3 个评论
显示 1更早的评论隐藏 1更早的评论

mado 2013-8-21

编辑：Walter Roberson 2013-8-21

ok, i know that Analog Input Channels 0 to 7—For single-ended measurements, each signal is an analog input voltage channel. For differential measurements, AI 0 and AI 4 are the positive and negative inputs of differential analog input channel 0. The following signal pairs also form differential input channels: <AI 1, AI 5>, <AI 2, AI 6>, and <AI 3,AI 7>.

how to verify writing , i think it's written right

Walter Roberson 2013-8-21

If you have checked your wiring, then I suggest you open a case with MATLAB technical support. I do not have the software or equipment to go further on this myself.

请先登录，再进行评论。

请先登录，再回答此问题。