已回答
reinforcement learning train-progress
Hi, If you have saved the training results, you can use this function to recreate the plot.

2 years 前 | 0

| 已接受

已回答
How do I randomize the value in a constant block for a local reset function for RL training
The num2str([10 10 10]) evaluates to '10 10 10' without brackets which is what causes the problem. Instead, just put '[10 10 10]...

2 years 前 | 0

| 已接受

已回答
Example: Train DDPG Agent to Swing Up and Balance Pendulum: Where are mechanical constants initialized ?
I am assuming the question is about this example. Inside the pendulum subsystem, we are modeling the equation (I + ml^2) theta_...

2 years 前 | 1

| 已接受

已回答
How to send values to workspace during reinforcement agent validation for further plot and analysis. Using "RUN" button on Simulink produces some difference from Validation.
Hello, First, to answer your point about the simulation differences between using the "Play" button vs using the "sim" command ...

2 years 前 | 0

| 已接受

已回答
MPC Toolbox : How to set "time optimal" Control problem using Custom Constrain function?
Hello, Unfortunately you cannot solve time-optimal problems with Model Predictive Control Toolbox because time cannot be used a...

2 years 前 | 0

| 已接受

已回答
Is it possible to provide output anticipation with the non linear Model Predictive Toolbox?
Hello, Yes it is possible to use previewing with nonlinear MPC, here is an example that shows how to do that.

2 years 前 | 0

| 已接受

已回答
How to extract the trained RL agent in MATLAB to C++?
Please take a look at this doc page.

2 years 前 | 0

| 已接受

已回答
In Simulink unable to change the simulation time
During training, each episode/simulation will last for Tf seconds at most. It may end sooner depending on the value of MaxStepsP...

2 years 前 | 0

| 已接受

已回答
Does Simulink Coder support code generation of custom solver functions for Nonlinear MPC blocks?
Hi Arnold, Unfortunately, right now you can only generate code using 'fmincon'. Custom nlp solvers can currently only be used f...

2 years 前 | 0

| 已接受

已回答
Invalid size or type for observation specification. Simulink Environment for Reinforcement Learning
I had a look at the attached zip. The error is on line 33 in 'Tentativo1.m'. This line should be mdl = 'RL'; % make sure your ...

2 years 前 | 0

已回答
Error while training a two-agent environment: Action specification of agent at index 2 incompatible with environment
The issue seems to be that the action specifications do not match what the environment model expects. Whether you are using Simu...

2 years 前 | 0

已回答
Using MPC Designer App with Plant Dynamics Model containing multiple Sign blocks
It seems like you have some kind of switched system (?). If that's the case, maybe try to linearize each dynamic model/"sign" se...

2 years 前 | 0

已回答
constraint on action space somehow that each action can be chosen only once
Unfortunately, this is not possible as of R2022b out of the box. You would need to create a custom agent to implement this behav...

2 years 前 | 0

已回答
Extended Kalman Filter state transition parameters
Glad you figured it out. By the way, this example shows the general workflow of using NLMPC + EKF with additional parameters

2 years 前 | 0

已回答
RL Stop training criteria
I believe that for event-based training, you need to adjust your stopping/saving criteria accordingly. For example the agent wil...

2 years 前 | 0

已回答
How to adjust internal sample time of MPC?
There is a way to do that, but first you need to consider whether you actually need to run your MPC controller that fast. As you...

2 years 前 | 0

| 已接受

已回答
Transfer a variable at the end of one episode to the next episode when training an agent in RL
The way to do this would be using the reset function mechanism provided in Reinforcement Learning Toolbox. Please take a look at...

2 years 前 | 0

已回答
DDPG Agent: Noise settings without any visible consequence
Your standard deviation is very high compared to the action range that you have set. As a result, when noise is added to the tan...

2 years 前 | 0

已回答
Reinforcement learning agent stops training unexpectedly?
The picture also mentioned why training stopped in the last two rows. In this case, it seems you have a criterion that stops tra...

2 years 前 | 0

已回答
Reinforcement learning unable to dupilcapte the best reward i had during training
Just because the reward of a single episode meets the desired performance, this does not mean that when you stop ttraining you s...

2 years 前 | 0

已回答
Triggering an action of an RL agent in a Simulink environment (SimEvents) via event
As of R2022a you can train reinforcement learning agents with event-based simulations. Please take a look at the release notes h...

2 years 前 | 0

已回答
Agent diverge after converge usingTD3
Please see answer here. This behavior could happen if the optimization moves to explore a different direction. I would suggest s...

2 years 前 | 0

已回答
Use of RL Agent instead of PID
Here is an example that does exactly what you mentioned, i.e. replaces a PID controller with an RL Agent

2 years 前 | 0

已回答
My agent finds a good solution but it does not repeat it and turns back to bad behavior again (Reinforcement Learning )
This picture shows progress for a very small number of episodes. You should wait for a few hundred episodes before you can evalu...

2 years 前 | 0

已回答
Oscillating reward in DDPG using Matlab Reinforcement learning toolbox with simulink environment
I think I have mentioned this in another post as well, but you should not expect your episode reward to be monotonic. Once it "c...

2 years 前 | 0

已回答
How to Use the Reinforcement Learning Toolbox to Draw Observations While Training？
You can use the information on plotting and visualization from this page to plot/visualize information during training

2 years 前 | 0

已回答
Determine the reward value to stop training in RL agent
For some problems you may be able to calculate what the maximum reward that can be collected in an episode is, so you can use th...

2 years 前 | 0

| 已接受

已回答
How to assign values to MV Targets of MPC object from cell array
You could specify values individually mpcobj.MV(1).Target=99; mpcobj.MV(2).Target=10; or you could do it in one line as follo...

2 years 前 | 0

| 已接受

已回答
problem with MPC controller
It seems to me that the solution is to add a constraint on the rate of change of the manipulated variable Ic. That way you can a...

2 years 前 | 0

已回答
How can I have 'measured states' in a MPC controller object in Simulink?
Model Predictive Control Toolbox includes built-in Kalman filters for the linear MPC API and blocks. So you really don't need to...

2 years 前 | 0

| 已接受