已回答
embedded coder cant generate reuseable function
Hi @chen lan, I understand that Embedded Coder generating multiple functions instead of reusing a single function for your reus...

9 months 前 | 0

已回答
Parameter Estimation of a servo motor does not track well.
Hi @ashanni sonny, I understand that you are facing challenges in accurately modelling the servo motor’s behaviour. The issue s...

9 months 前 | 0

| 已接受

已回答
Power measurement (electric motor)
Hi @Jack Daniels, To measure the active power, reactive power, apparent power, and power factor for your three-phase motor simu...

9 months 前 | 0

已回答
Power Electronics Simulation Onramp Model Fidelity Part Bugged
Hi @Furkan, I couldn't able to reproduce the issue, it is working fine from my end. If it still persists you can refer to th...

9 months 前 | 0

| 已接受

已回答
C2000 Synchronization of ePWM modules with external signal
Hi @Roberto, To configure ePWM1, ePWM2, ePWM3, and ePWM4 for synchronization using an external signal connected to GPIO40, you...

9 months 前 | 0

已回答
Three phase dynamic load fails earlier than expected
Hi @Despoina Papageorgiou, I understand that you are facing an issue with the Three-Phase Dynamic Load in your Simulink model,...

9 months 前 | 0

已回答
BlockIO output set to zero when multiple blocks are used
Hi @Aaron Troll, I understand you are facing issues with Simulink blocks generated by the IO Device Builder app, where multiple...

9 months 前 | 0

已回答
How can I remove this warning:Estimated channel modulation for data extrapolation must be greater than zero. Use linear extrapolation.
Hi @Ignacio, I understand that you are facing an extrapolation error while simulating N Channel MOSFET model. The issue arise...

9 months 前 | 1

| 已接受

已回答
Can I give Modulated Sine Wave as Input to CMPA of ePWM Block in MATLAB Simulink for SVPWM Generation ?
Hi @PANDIT DHANRAJ SURESH I understand that you are working on a 3-phase inverter using the TI Delfino F28379D LaunchPad and a...

9 months 前 | 0

已回答
Pi Control plant cannot be linearized
Hi @Muhamed Ehab The errors "Subscript no. 2 is out of range" and "Plant cannot be linearized" occur because your model include...

9 months 前 | 0

已回答
How to generate a stationary car and define the direction of the vehicle via matlab in Roadrunner
Hi @Xinyu Yang I understand that you want to import stationary vehicles into RoadRunner and ensure they are oriented parallel t...

9 months 前 | 0

已回答
modeling an advanced energy management system for electric vehicles using MATLAB/Simulink
Hi Salih, To model your advanced energy management system (EMS), for electric vehicle you can follow the below steps: Firstly...

9 months 前 | 1

已回答
problems encountered in DDPG.
Hi 邓龙京, The error message “Number of input layers for state-action-value function deep neural network must equal the number of...

10 months 前 | 0

已回答
Error in rl.agent.AbstractAgent/train while executing example "Train Reinforcement Learning Agent in MDP Environment"
Hi @David Carrasco Martínez, I understand that you are facing an issue when “doTraining” flag is set to “true” in "Train Reinf...

10 months 前 | 0

已回答
Train a DQN Agent: RL Simulink with Simscape (Error: Discontinuities detected within algebraic loop)
Hello, I understand that you are trying to replace a PI controller with a DQN agent for your Buck Converter model and encounte...

10 months 前 | 0

已回答
get error runing TrainTD3AgentForPMSMControlExample.mlx
Hi @hai hu, I understand that you are facing an issue in the "TrainTD3AgentForPMSMControl" example model when “doTraining” fla...

10 months 前 | 0

已回答
I am finding it difficult to design a 50MW VSC PV inverter.
Hi Prithwi, I understand that you are facing an issue in obtaining the desired output power. You can try the below suggestions...

10 months 前 | 0

已回答
Error in solver configuration
Hi Pranjali, The error message "Input voltage must be greater than or equal to zero" suggests that your DC-DC converter is rec...

10 months 前 | 0

已回答
Simscape Electrical: access "Display Assosciated Initial Conditions" programmatically
Hi Fredrik, To automatically set initial conditions for multiple synchronous machines using load flow results, you can follow ...

10 months 前 | 0

已回答
Simulink stepper motor control
Hi Zsombor, To achieve continuous motor control independent of Simulink's sample time, you can use hardware interrupts or time...

10 months 前 | 0

已回答
how can we plot the voltage trajectory of pmsm motor , when we have vd and vq data from simulink?What kind of plot is this?
Hi Deepak, To plot the voltage trajectory of a Permanent Magnet Synchronous Motor (PMSM) using the data from Simulink, you ...

10 months 前 | 0

已回答
How to change SPWM Frequency of Arduino mega 2560 with MATLAB SIMULINK
Hi yahya, The output pulses from your Simulink model appears to be generated with frequency of "sin wave" so this is why the a...

10 months 前 | 0

已回答
Simulink model control servo by mpu9250
Hi Aseel, To control servo motor using one of the yaw, pitch, or roll angles derived from your MPU9250 sensor in Simulink, you...

10 months 前 | 0

已回答
PSCAD, Matlab interfacing
Hi Mohamed, To synchronize the timing of your MATLAB script with the PSCAD simulation, you need to ensure that your MATLAB cod...

10 months 前 | 0

已回答
What is the best method to model or utilize the built-in model for a three-phase voltage regulator in MATLAB Simulink, specifically for the IEEE 34 distribution network?
Hi Asi, To model a three-phase voltage regulator in MATLAB Simulink for the IEEE 34 distribution network and with load flow an...

10 months 前 | 0

已回答
detect and remove motion artifacts from ppg signal using lms adaptive filter
Hi Rajesh, I understand that you are looking for a method to remove noise from motion artifacts in a PPG signal. You can fol...

10 months 前 | 0

已回答
Failed to load OpenDRIVE data: Failed to convert '-'
Hi, It looks like you are facing an error because there is an invalid character, like '-' where a number should be, in your fi...

10 months 前 | 0

已回答
How to connect simpowersystem generic battery block to the simscape blocks without an algebraic loop error?
Hi Yurdakul, I understand that you are trying to connect a SimPowerSystems battery block to Simscape components and faci...

10 months 前 | 0

已回答
Synchronous machine model incorrectly initializes when taking into account saturation
Hi Solis, I understand that you are facing an issue with the initialization of a synchronous machine model when accounting for...

11 months 前 | 1

| 已接受

已回答
how can i account charge and discharge of battery in ev modeling.
Hi Gokarna, I understand that you are trying to model both the charge and discharge behaviour of a battery in an electric vehi...

11 months 前 | 0