已回答
PX4 toolbox error: build,deploy on run on Pixhawk 6x
We are looking into this issue. Set the following preference in your MATLAB command window and try building the model again

1 year 前 | 0

| 已接受

已回答
PX4 HIL with Pixhawk 6x : HIL with simulink plant dynamics using Sik Telemetry Radio. Could not connect to target application: XCP serial port error
Note that from MATLAB & Simulink, the Wireless Monitor & Tune workflow has not been tested. This workflow sometimes works, but ...

1 year 前 | 0

| 已接受

已回答
Code generation information file does not exist while building px4 firmware
Can you change the directory where you are changing the code? The length of the current path is too long and Windows has a limit...

1 year 前 | 0

已回答
PX4 SITL with simulink based plant model, system not found
Thanks for reporting this issue. This a bug and we are working to push the fix out. I am attaching 3 MATLAB scripts in this answ...

1 year 前 | 0

| 已接受

已回答
PX4 HIL with Pixhawk 6x : HIL with simulink plant dynamics using Sik Telemetry Radio
The COM port should be one over which you want to communication between plant and Autopilot to happen. If you want the MAVLink d...

1 year 前 | 0

| 已接受

已回答
Upload custom flight controller on Pixhawk 4, and flight tests
Check if the board is in HITL mode. In HITL mode, the actuator pins are disabled. If you want to run the engines, then you have ...

1 year 前 | 0

| 已接受

已回答
PX4 toolbox in Simulink:when performing SITL with Jmavsim error code -10
This error indicates there might be data drop while sending data between Host Target and Simulink in External Mode. But External...

1 year 前 | 0

| 已接受

已回答
Why am I receiving "fatal error: algorithm: No such file or directory" from the MAVLink Serializer block during Build & Deploy on a Pixhawk 1?
The MAVLink blocks in Simulink can only be deployed on a Linux target as mentioned here. The Pixhawk board does not rub Linu...

1 year 前 | 1

| 已接受

已回答
UAV Toolbox Support Package Alternative?
We are currently working on supporting PX4 1.14 in UAV Toolbox support package for PX4 Autopilots. We will let you know when the...

2 years 前 | 0

已回答
QGroundControl doesn't recognize Pixhawk 6x
In HITL mode, the Pixhawk 6x is not supposed to connect directly to QGroundcontrol but via the MAVLink bridge in the Simulink pl...

2 years 前 | 1

已回答
Why the PX4 firmware version supported by the Pixhawk 6x (minimum version 1.13.1) and the firmware version supported by the UAV Toolbox Support Package for PX4 Autopilots (ver
The support for Pixhawk 6x is available in PX4 Firmware v1.12.3. Can you elaborate on what do you mean by COM port disappears? W...

2 years 前 | 0

已回答
Pixhawk 6X / 5X / 6C support by Simulink
Pixhawk 6x is now a supported targe in R2023a version of MATLAB in the latest release of UAV Toolbox support ackage for PX4 Auto...

2 years 前 | 0

已回答
Store data using the "To File" or " to workspace" block when using the PX4 toolbox on Simulink performing code generation
Logging data using To workspace block is only supported when you deploy to Pixhawk hardware. In SITL or PX4 Host Target, To work...

2 years 前 | 0

| 已接受

已回答
Can I use Pixhawk6C instead of Pixhawk4 when using UAV toolbox support packages for PX4 autopilots?
We are currently working on developing support for Pixhawk 6c. BTW, we don have support for Pixhawk 6x board in R2023a. So if yo...

2 years 前 | 0

已回答
Pushing a custom simulink UAV model to px4.
Have you tried out thecontroller deployment examples in the support package? The support package already contains controller dep...

2 years 前 | 1

| 已接受

已回答
Pixhawk 6X / 5X / 6C support by Simulink
Pixhawk 6x can be used with AV Toolbox Support Package for PX4 Autopilots in R2022b and R2023a. Follow the steps mentioned here....

2 years 前 | 0

| 已接受

已回答
Is it possible to use the pixhawk 6x with the "UAV toolbox support package for PX4 autopilot"?
Pixhawk 6x can be used with AV Toolbox Support Package for PX4 Autopilots in R2022b and R2023a. Follow the steps mentioned here....

2 years 前 | 0

已回答
How do I use Pixhawk 6x with UAV Toolbox Support Package for PX4 Autopilots?
Pixhawk 6x is officially supported in the latest version UAV Toolbox support package for PX4 Autopilots in R2023a. It is recomme...

2 years 前 | 0

| 已接受

提问

How do I use Pixhawk 6x with UAV Toolbox Support Package for PX4 Autopilots?
I want to use the Pixhawk 6x board with the UAV Toolbox Support Package for PX4 Autopilots. What are the steps that I can follow...

2 years 前 | 1 个回答 | 0

1

个回答

已回答
BOAT Autopilot simulation using PX4
The PX4 support package allows the users to design controllers in Simulink, generate the code for the same and deploy on hardwar...

2 years 前 | 0

已回答
Why do I receive Code generation information file does not exist?
This issue is most likely due to GCC unable to find a package while compilation in your Ubuntu 20.04 installation. There are wor...

2 years 前 | 0

已回答
UAV Toolbox Support Package for PX4 Autopilots - px4_simulink_app module
Before I answer your question, let me clarify that the "PX4 default startup script rcS" is the recommended option for booting up...

2 years 前 | 0

| 已接受

已回答
Pixhawk 6C support (PX4 fmu-v6c)
We have verified and tested the features in R2022b with firmware version v1.12.3. Firmware version 1.13 is not officially suppor...

2 years 前 | 0

| 已接受

已回答
How can I use RL Agent with PX4 Host Target?
Manually closing this question as user has been recommended to reach out to MathWorks Tech Support

2 years 前 | 0

已回答
Deployment of Simulink designed controller to Pixhawk Cube Orange
The support for Cube Orange is available from R2022b. As Arun pointed out, follow the documentation to understand how to deploy ...

2 years 前 | 0

已回答
UAV Toolbox Support Package for PX4 Autopilots Install Failed
The error syndrome mentioned in the log looks similar to what has been mentioned here. I would recommend you to upgrade your MAT...

2 years 前 | 0

| 已接受

已回答
THE CUBE ORANGE / PX4 SUPPORT PACKAGE TOOLBOX CONNECTION PROBLEM !!
The R2022b release of UAV Toolbox Support Package for PX4 Autopilots now provides the facility to deploy code on Cube Orange boa...

2 years 前 | 0

已回答
UAV toolbox PX4 cube orange Compatability
The R2022b release of UAV Toolbox Support Package for PX4 Autopilots now provides the facility to deploy code on Cube Orange boa...

2 years 前 | 0

已回答
UAV Toolbox Support Package for PX4 Autopilots - Hardware Setup Build PX4 Firmware Failed
First thing I would suggest is build the Firmware using the Cygwin Terminal in the new PC. You can run the command make px4_sitl...

2 years 前 | 0

| 已接受

已回答
I have no idea about add on "UAV toolbox support package for px4 autopilot"
Can you send us the installation log where we can see the detailed log. To get the installation log Open MATLAB where you t...

3 years 前 | 0