socAXIManager

For an example of how to configure and use the AXI manager IP in your design, see Random Access of External Memory Using AMD Devices (SoC Blockset). Specifically, review the soc_image_rotation_axi_master.m script that initializes the memory on the device, starts the FPGA logic, and reads back the modified data. This example shows only the memory initialization step.

Load a .mat file that contains structures derived from the board configuration parameters. This file was generated by SoC Builder. These structures also describe the IP cores and memory configuration of the design on the board. Set up a JTAG AXI manager connection by creating a socHardwareBoard (SoC Blockset) object and passing it to the socAXIManager object. The socAXIManager object connects with the hardware board and confirms that the IP is present.

load('soc_image_rotation_zc706_aximaster.mat');
hwObj = socHardwareBoard('Xilinx Zynq ZC706 evaluation kit','Connect',false);
AXIManagerObj = socAXIManager(hwObj);

Initialize the memory contents on the device by loading the figure data and writing it to Region1. The FPGA logic is designed to read this data, rotate it, and write it into Region2. Clear the contents of Region2.

load('soc_image_rotation_inputdata.mat');
inputFigure = smallImage;
[x, y] = size(inputFigure);
inputImage = uint32(reshape(inputFigure',1,x*y));
writememory(AXIManagerObj,memRegions.AXI4MasterMemRegion1,inputImage);
writememory(AXIManagerObj,memRegions.AXI4MasterMemRegion2,uint32(zeros(1,x*y)));

For this example, you must have a design running on a hardware board connected to the MATLAB host machine.

Create a MATLAB AXI manager object. The object connects with the hardware board and confirms that the IP is present. You can create the object with a vendor name or an socHardwareBoard object.

mem = socAXIManager('Xilinx');

Write and read one or more addresses with one command. By default, the functions auto-increment the address for each word of data. For instance, write ten addresses, then read the data back from a single location.

writememory(mem,140,[10:19])
rd_d = readmemory(mem,140,1)

rd_d =

  uint32

   10

Now, read the written data from ten locations.

rd_d = readmemory(mem,140,10)

rd_d =

  1×10 uint32 row vector

   10   11   12   13   14   15   16   17   18   19

Set the BurstType property to 'Fixed' to turn off the auto-increment and access the same address multiple times. For instance, read the written data ten times from the same address.

rd_d = readmemory(mem,140,10,'BurstType','Fixed')

rd_d =

  1×10 uint32 row vector

   10   10   10   10   10   10   10   10   10   10

Write incrementing data ten times to the same address. The final value stored in address 140 is 29.

writememory(mem,140,[20:29],'BurstType','Fixed')
rd_d = readmemory(mem,140,10)

rd_d =

  1×10 uint32 row vector

   29   11   12   13   14   15   16   17   18   19

Alternatively, specify the address as a hexadecimal string. To cast the read data to a data type other than uint32, use the OutputDataType property.

writememory(mem,'1c',[0:4:64])
rd_d = readmemory(mem,'1c',16,'OutputDataType',numerictype(0,6,4))

rd_d = 

  Columns 1 through 10
         0    0.2500    0.5000    0.7500    1.0000    1.2500    1.5000    1.7500    2.0000    2.2500
  Columns 11 through 16
    2.5000    2.7500    3.0000    3.2500    3.5000    3.7500

          DataTypeMode: Fixed-point: binary point scaling
            Signedness: Unsigned
            WordLength: 6
        FractionLength: 4

When you are done accessing the board, release the JTAG connection.

release(mem)

When multiple JTAG cables are connected to your host computer, the object prioritizes Digilent cables over FTDI cables. To use an FTDI cable, specify the JTAG cable type property.

h = socAXIManager('Xilinx', 'JTAGCableType', 'FTDI')

If two cables of the same type are connected to your host computer, specify the JTAGCableName property for the board where the JTAG manager IP is running. To see the JTAG cable identifiers, attempt to create an socAXIManager object, which, in this case, errors and returns a list of the current JTAG cable names.

h = socAXIManager('Xilinx')

Error using fpgadebug_mex
Found more than one JTAG cable:
0 (JtagSmt1): #tpt_0001#ptc_0002#210203991642
1 (Arty): #tpt_0001#ptc_0002#210319789795
Please disconnect the extra cable, or specify the cable name as an input argument.
See documentation of FPGA Data Capture or MATLAB as AXI manager to learn how to set
the cable name.

To communicate with this Arty board, specify the matching JTAG cable name.

h = socAXIManager('Xilinx','JTAGCableName','#tpt_0001#ptc_0002#210319789795')