There is no visualization in the animation window mechanics explorers?

20 次查看（过去 30 天）
Aleksandr Panov
Aleksandr Panov 2014-2-6
回答： George 2024-5-2
Hi! I Decided to start using SimMechanics and faced with the problem of visualization in Mechanics Explorers. As an example, open a standard project Robot Arm Model and run it. Robot animation is not shown.
What's the problem?
Windows 7, MatLab/Simulink 2013b x64, SimMechanics 4.3. Intel Core i5, Nvidia GTX 660 Ti.
Thanks!

请先登录，再回答此问题。

采纳的回答

Christoph Hahn
Christoph Hahn 2016-3-22
Hi Aleksandr,
you can switch of the visualization in the Mechanics Explorer. Just have a look at the attached screenshots.
  • Click the gear icon
  • Go to SimMechanics 2G -> Explorer and switch visualization on/off.
Best regards, Christoph
  3 个评论
显示 1更早的评论
Arafat Mukasa
Arafat Mukasa 2017-11-23
I faced the same challenge and this is how i solved it. Hopes it helps. Always ensure that the CAD models and the simscape multibody model are in the same current folder in matlab/simulink. Please refer to the screenshots below. As you can see from the current folder, the different parts of my CAD model (for example frame.SLDPRT) are in the same folder with the simscape multibody model (quadrotor_complete.slx).
Assuming all the above is in place and still the visualization is blank, then do the following with guidance from the screenshot attached; Choose a part of your model (in my case it were frame_1_RIGID), right click and then select show everything.
Rony Rony
Rony Rony 2020-4-24
The explorer open but the animation were not visualize , no component had been shown a gray screen is only visible @ Christoph Hahn

请先登录，再进行评论。

更多回答（4 个）

Arafat Mukasa
Arafat Mukasa 2017-11-23
I faced the same challenge and this is how i solved it. Hopes it helps. Always ensure that the CAD models and the simscape multibody model are in the same current folder in matlab/simulink. Please refer to the screenshots below. As you can see from the current folder, the different parts of my CAD model (for example frame.SLDPRT) are in the same folder with the simscape multibody model (quadrotor_complete.slx).
Assuming all the above is in place and still the visualization is blank, then do the following with guidance from the screenshot attached; Choose a part of your model (in my case it were frame_1_RIGID), right click and then select show everything.
Damian Keretic
Damian Keretic 2020-4-7
Did someone find the way to solve this problem? I have exactly the same situation. Visualization is just blank grey window.
I tried the thing that Arafat Mukasa proposed but it doesn't work.
  2 个评论
saleh fahjan
saleh fahjan 2020-4-9
same problem, tried to do thing up here nothing changed still no visualiziation any help ?
Rony Rony
Rony Rony 2020-4-24
hello did you get the sollution I have the same problem, please inform me if you got the solution.

请先登录，再进行评论。

Xinyang Tian
Xinyang Tian 2020-5-17
编辑：Xinyang Tian 2020-5-17
Hi,gays,i have some solutions to solve this problem ~
1.Disabling the Geforce driver from device manager
2.Check the name of your simulink model,make sure there are no garbled codes. The following figures shows the specific check steps.
Hope to help those in need.
George
George 2024-5-2
Mechanics Explorer doesn's seem to work if you are in Accelerator mode. Run simulation in normal mode and it should pop up. At least, that was the problem with my version.

类别

在 Help Center 和 File Exchange 中查找有关 Simulation and Analysis 的更多信息

标签

产品

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by