Accessing Matlab Cluster from outside the network
5 次查看(过去 30 天)
显示 更早的评论
Hi,
In my lab we have a Matlab Cluster running. The thing is, we would like to access it from outside of the local network. I guess that we could set up a VPN, but I would like to avoid that if possible. What are the ports that should be open for this to work? I was thinking in perhaps make a SSH Tunnel from home to the lab, but I'm not sure if it will work.
Any help? Thanks in advance!
0 个评论
回答(1 个)
Thomas Ibbotson
2014-4-3
I'm assuming you're using MJS. This is what the documentation has to say:
BASE_PORT. The mdce_def file specifies and describes the ports required by the job manager and all workers. See the following file in the MATLAB installation used for each cluster process:
matlabroot/toolbox/distcomp/bin/mdce_def.sh (on UNIX operating systems) matlabroot\toolbox\distcomp\bin\mdce_def.bat (on Windows® operating systems)
in R2014a this file specifies the following:
# BASE_PORT: The base port of the mdce service.
# The mdce service will use as many ports as needed, starting with BASE_PORT.
# On a machine that runs a total of nJ job managers and nW workers, the mdce
# service reserves a total of 5+nJ+3*nW consecutive ports for its own use.
# All job managers and workers, even those on different hosts, that are going
# to work together must use the same base port, otherwise they will not be
# able to contact each other. In addition MPI communication will occur on ports
# starting at BASE_PORT+1000 and using up nW consecutive ports.
# Some operating systems are reluctant to immediately free TCP ports from the
# TIME_WAIT state for use by the same or other processes, so you should allow
# unfirewalled communication on 2*nW ports for MPI communications.
# To connect from MATLAB to a cluster with a non-default BASE_PORT, the
# value of BASE_PORT must be appended to the 'Host' property in the MJS
# cluster profile, in the form Hostname:BASE_PORT (e.g., myMJSHost:44001).
BASE_PORT="27350"
So as an example if you have a head node running 1 MJS with 4 workers you would need to give access from the client to the head node on ports 27350-27368 (18 ports = 5 + 1 + 3*4).
However, this is not sufficient to have a full working system, the head node also needs to be able to connect to server sockets created on the client to be able to transfer 'large' data, and the workers need to connect back to the client to form a parallel pool.
Again here's the documentation:
With the pctconfig function, you specify the ports used by the client. If the default ports
cannot be used, this function allows you to configure ports separately for communication with
the job scheduler and communication with pmode or a parallel pool.
These ports are set by default (in R2014a) to 27370-27470.
In summary, with the default configuration and 4 workers on the head node only, you should forward ports 27350-27368 from the client to the server, and you should forward ports 27370-27470 from the server to the client.
I should note that in our experience using SSH port forwarding to make this available outside your network does not perform well, but of course your mileage may vary.
3 个评论
Marco
2014-4-3
I am not Thomas, to whom you asked back, but let me say that VNC and alike software might be the very easiest way for you to access a computer from remote. Often it works via the same port as used for HTTP transfer, and therefore no special, extra firewall settings might be needed. You use your computer at home as keyboard, mouse and monitor, and work at your computer elsewhere installed. You can stop your remote control session leaving everything on your remote computer running. When you login in to it again, by remote control - or locally - , you find it exactly as you left it and just continue with your work. Give it a try before, before getting to complicated with other solutions.
Adib Yusof
2021-1-24
Hii. I'm trying to do the same. I'm not a system admin or anything, but needs to setup this for my lab. What's the current best way to do this? Also, is there any detailed tutorial to change the ports or VPN? I tried following some videos on YouTube but it didn't work, and now I think the videos might be not the correct one for this purpose. Thankss!
另请参阅
类别
在 Help Center 和 File Exchange 中查找有关 Installation 的更多信息
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!