How to generate multiple .stl files in a loop?

3 次查看（过去 30 天）
Hasnain Raja Muhammad
评论： Hasnain Raja Muhammad 2021-9-16
My core question is: How to write multiple .stl files.
What I am doing here is: Open a .stl file (Code line 1), then rotate it in randomly generated axis (Code lines: 2 : 16) and finally write 10 .stl files.
When I run my codes, in command window it show 10 files succesfully written, but when I check in directory it shows only 1 file.
I think there is something wrong with the way I am try to use stlread (function) in for loop to write multiple .stl files.
Link1: function used to read .stl file
Link2: function used to write .stl file
[F,V,N] = stlread ('Directory_name:\Model_STL_Binary_0_0_0.stl'); %.stl file location
theta_x = randi ([0,180],10,1);
theta_y = randi ([0,180],10,1);
theta_z = randi ([0,180],10,1);
T = table(theta_x,theta_y,theta_z);
theta_angles =table2array(T);
ax = deg2rad(theta_angles(:,1));
ay = deg2rad(theta_angles(:,2));
az = deg2rad(theta_angles(:,3));
for i= 1:length(theta_angles)
Rx = [ 1, 0, 0 ; 0, cos(ax(i)), -sin(ax(i)); 0, sin(ax(i)), cos(ax(i))];
Ry = [ cos(ay(i)), 0, sin(ay(i)) ;0, 1, 0 ; -sin(ay(i)), 0, cos(ay(i)) ];
Rz = [ cos(az(i)), -sin(az(i)), 0 ; sin(az(i)), cos(az(i)), 0 ; 0, 0, 1 ];
pointR1 = V*Rx;
pointR2 = pointR1*Ry;
pointR3 = pointR2*Rz;
stlwrite('check.stl', F, pointR3(:,1:3));
end

请先登录，再回答此问题。

采纳的回答

KSSV
KSSV 2021-9-16
You are overwriitng the stl files. Always you are using the same name to .stl file. You need to give different filename; check the below addition.
[F,V,N] = stlread ('Directory_name:\Model_STL_Binary_0_0_0.stl'); %.stl file location
theta_x = randi ([0,180],10,1);
theta_y = randi ([0,180],10,1);
theta_z = randi ([0,180],10,1);
T = table(theta_x,theta_y,theta_z);
theta_angles =table2array(T);
ax = deg2rad(theta_angles(:,1));
ay = deg2rad(theta_angles(:,2));
az = deg2rad(theta_angles(:,3));
for i= 1:length(theta_angles)
Rx = [ 1, 0, 0 ; 0, cos(ax(i)), -sin(ax(i)); 0, sin(ax(i)), cos(ax(i))];
Ry = [ cos(ay(i)), 0, sin(ay(i)) ;0, 1, 0 ; -sin(ay(i)), 0, cos(ay(i)) ];
Rz = [ cos(az(i)), -sin(az(i)), 0 ; sin(az(i)), cos(az(i)), 0 ; 0, 0, 1 ];
pointR1 = V*Rx;
pointR2 = pointR1*Ry;
pointR3 = pointR2*Rz;
filename = strcat('check_',num2str(i),'.stl') ; % File name based on loop index
stlwrite(filename, F, pointR3(:,1:3));
end

更多回答（0 个）

类别

在 Help Center 和 File Exchange 中查找有关 STL (STereoLithography) 的更多信息

标签

产品


版本

R2018a

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by