MATLAB libraries of DHT11 sensor

Question

Sadiq Akbar 2021-11-20

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1591279-matlab-libraries-of-dht11-sensor

评论： Walter Roberson 2022-12-7

If the DHT11 sensor is connected to my Arduino and I want to read the temperature and humidity data directly from that pin of Arduino to which it is attached without the help of any arduino code, is there any Matlab library available for that?

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

MathWorks MATLAB Hardware Team 2021-11-22

Hi Sadiq,

Kindly reach out to MathWorks Technical Support to get help in resolving your query

https://www.mathworks.com/support/contact_us.html

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Walter Roberson 2021-11-20

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1591279-matlab-libraries-of-dht11-sensor#answer_836099

No, there is no MATLAB library for that.

However if you are using Simulink, see https://www.mathworks.com/matlabcentral/fileexchange/62878-arduino-additional-sensors-library-dht-lps331

Otherwise,

https://www.mathworks.com/matlabcentral/answers/521420-i-want-to-interface-with-the-dht11-sensor-in-matlab-but-program-give-this-error-subscripted-assignm

4 个评论
显示 2更早的评论隐藏 2更早的评论

Sadiq Akbar 2021-11-20

编辑：Sadiq Akbar 2021-11-20

在 MATLAB Online 中打开

I have modefied that code like below:

clc
clear all
delete(instrfindall);
close(instrfindall);
s = serial('COM5');
time=100;
i=1;
while(i<time)
    fopen(s)
    fprintf(s, 'Your serial data goes here')
    out = fscanf(s)
    
    Temp(i)=str2double(out(1:4));% Temp(i)=str2num(out(1:4));
    subplot(211);
    disp(Temp(i))% By Me
    plot(Temp(i),'g');% plot(Temp,'g');
    axis([0,time,10,50]);
    title('Parameter: DHT11 Temperature');
    xlabel('time');
    ylabel('Temperature');
    grid
    
    
    Humi(i)=str2double(out(5:9));
    subplot(212);
    disp(Humi(i))% By Me
    plot(Humi(i),'m');
    axis([0,time,10,100]);
    title('Parameter: DHT11 Humidity');
    xlabel('time');
    ylabel('% of Humidity');
    grid
    
    fclose(s)
    i=i+1;
    drawnow;
end
delete(s)
clear s

But when I execute it in debugger mode, and I check the variable out, tooltp shows: out: 1 x 20 char=

Temperature: 18.00

Likewise when I check Temp(i), the debgger shows in tooltip as:

Temp: 1 x 20 double=

NaN

Also no any graph is displayed.

Sébastien Josset 2022-12-7

Hi! The answer would interest me as well :) When using Sadiq's modified code, I get:

Warning: Unsuccessful read: A timeout occurred before the Terminator was reached.

'serial' unable to read all requested data. For more information on possible reasons, see Serial Read Warnings.

out =

'nannannannannannannannan'

NaN

Some help would be great!

Sebi

Walter Roberson 2022-12-7

If "out" is showing Temperature: 18.00 then the implication is that the data sent by the other side is not just numeric. If you know for sure that the "Temperature:" part is always going to be there then you can use fscanf() with a format of 'Temperature: %f' to read the numeric part directly, but if there might be a variety of text then you need to analyze the text to figure out which format to use.

请先登录，再进行评论。

MATLAB libraries of DHT11 sensor

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

回答（1 个）

4 个评论
显示 2更早的评论隐藏 2更早的评论

另请参阅

类别

标签

Community Treasure Hunt

MATLAB libraries of DHT11 sensor

1 个评论 显示 -1更早的评论隐藏 -1更早的评论

回答（1 个）

4 个评论 显示 2更早的评论隐藏 2更早的评论

另请参阅

类别

标签

Community Treasure Hunt

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

4 个评论
显示 2更早的评论隐藏 2更早的评论