How to increase the size of "s" using pdegeom?

1 次查看(过去 30 天)
I have written a pdegeom file which produce a sinusoidal edge. The standard amount of grid points (size(s)) is set to 50. This is not enough to reproduce approx. 50 periods of the sinus correctly.
The pdegeom file (you can check it with pdegplot('Geom') to see that the sinus is not correctly plotted):
function [ x,y ] = Geom(bs,s)
nbs = 10;
if nargin==0
x=nbs;
return
end
dl=[ 0 1 2 3 4 5 6 7 8 9;
1 2 3 4 5 6 7 8 9 10;
0 0 0 0 0 0 0 0 1 1;
1 1 1 1 2 2 2 1 2 2];
if nargin==1
x=dl(:,bs);
return
end
x=zeros(size(s));
y=zeros(size(s));
[m,n]=size(bs);
if m==1 && n==1,
bs=bs*ones(size(s)); % expand bs
elseif m~=size(s,1) || n~=size(s,2),
error(message('pde:cardg:SizeBs'));
end
nn=size(bs,1)*size(bs,2);
if nn==0
x=[];
y=[];
return
end
for ibs=1:nn
switch bs(ibs)
case 1 % Boundary-Tip down right
xx=50 - (50-10)*s(ibs);
yy=-50 +0*s(ibs);
case 2 % Tip side right
xx=10 - (10-5)*(s(ibs)-1);
yy=-50*(1-(s(ibs)-1));
case 3 % Tip apex half
xx=5*cos(pi/2*(s(ibs)-2));
yy=5*sin(pi/2*(s(ibs)-2));
case 4 % Tip to resist
xx=0*(s(ibs)-3);
yy=5 + ((20-12)-5)*(s(ibs)-3);
case 5 % resist to sample
xx=0*(s(ibs)-4);
yy=(20-12) + (12)*(s(ibs)-4);
case 6 % Sample
xx=50*(s(ibs)-5);
yy=20 + 0*(s(ibs)-5);
case 7 % Boundary right - Resist
xx=50 + 0*(s(ibs)-6);
yy=20 - (12)*(s(ibs)-6);
case 8 % Boundary right
xx=50 + 0*(s(ibs)-7);
yy=(20-12) - ((20-12)-(-50))*(s(ibs)-7);
case 9 % Layer right - Tip side
xx=30*(s(ibs)-8);
yy=(20-12)+3*sin(2*pi/1*xx);
case 10
xx=30-(30-50)*(s(ibs)-9);
yy=20-12+0*(s(ibs)-9);
end
x(ibs)=xx;
y(ibs)=yy;
end
end

采纳的回答

Bill Greene
Bill Greene 2014-10-30
If your concern is about producing a nice looking plot from pdegplot, you will need to edit that function by changing the line:
n=50;
at around line 46 to make n something larger.
If your concern is about getting a sufficiently fine mesh near the sinusoid edge, you don't need to do anything but specify a sufficiently small value of hmax in the call to initmesh. initmesh will call your Geom function as often as needed to produce a mesh with an accurate boundary.
  1 个评论
Steve
Steve 2014-11-3
Thank you very much.
I tried to reduce hmax before and it seems to refine only the geometry produced by pdegplot. However now it works fine!

请先登录,再进行评论。

更多回答(0 个)

类别

Help CenterFile Exchange 中查找有关 Geometry and Mesh 的更多信息

产品

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by