Error:Each physical network must be connected to exactly one Solver Configuration block. There is no Solver Configuration block connected to Physical Network with the following blocks

Question

saideep 2014-11-10

8
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/162097-error-each-physical-network-must-be-connected-to-exactly-one-solver-configuration-block-there-is-no

回答： Joel Van Sickel 2024-6-10

I had connected a solver configuration block in my model but these error is popping up when i connect a "current-Voltage simscape interface" block in my model.Kindly guide me in solving this problem. Thanking you, Saideep.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Yogeshwar Bala 2018-10-6

16
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/162097-error-each-physical-network-must-be-connected-to-exactly-one-solver-configuration-block-there-is-no#answer_340063

Connect an "Electrical Reference" block to your ground line and add a Solver Configuration block with default value of f(x) = 0 to it.

5 个评论
显示 3更早的评论隐藏 3更早的评论

Reginald Ogu 2023-3-17

Please how can I add a Solver Configuration block to my Simscape model?

Huang YanMing 2024-3-4

To add a "Solver Configuration"

Go to library browser and find it in the below folder

Simscape>Utilities

请先登录，再进行评论。

Answer 2

Behnam Mohammad 2020-1-15

4
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/162097-error-each-physical-network-must-be-connected-to-exactly-one-solver-configuration-block-there-is-no#answer_410321

What happens when you have multiple subsystems and each subsystem has an individual solver?

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Answer 3

ever steeven nevarez cedeño 2021-8-31

1
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/162097-error-each-physical-network-must-be-connected-to-exactly-one-solver-configuration-block-there-is-no#answer_777604

tengo un problema similar pero al reves el problema es cuando lo pongo

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

ever steeven nevarez cedeño 2021-8-31

alguien que pueda ayudarme

请先登录，再进行评论。

Answer 4

Joel Van Sickel 2024-6-10

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/162097-error-each-physical-network-must-be-connected-to-exactly-one-solver-configuration-block-there-is-no#answer_1469581

This specific problem happens from the interface block. Those blocks are used to decouple simscape networks and if you look under the hood, you will see they are connected by simulink wires, not simscape wires. This means that if you use one, you will now have an additional simscape network, so you will need to add an additional simscape configuration block to the side of the network that doesn't already have one. Or you will need to add it to both sides if neither side has one.