What does my Root Locus response mean? Why is it different?

25 次查看（过去 30 天）
Joel Okanta
Joel Okanta 2022-3-31
编辑： Paul 2022-4-1
Right at the moment I am learning about Root Locus of the system and how they are normally used for damping/oscillating systems. I often see Magnetic Levitation Papers use these to determine the root locus, which I guess must be to determine the oscillations in their system. However, unlike their ones, mine is a bit different, only sitting at the real axis. Is this alright? I mean it does make sense since both my roots exist on the real plane, but I'm curious and want to know more as I cannot find any relevant info about MagLevs and root locuses anywhere else.
My system:
sys = tf([-19008],[960.704 0 -2376000])
rlocus(sys)
Results:
Relevant Papers
Both Taken from IEEE:
Links:
https://ieeexplore.ieee.org/document/8986710
https://ieeexplore.ieee.org/document/5570565

请先登录，再回答此问题。

回答（1 个）

Paul
Paul 2022-3-31
Hello @Joel Okanta
The root locus is much more general than as suggested in the Question. Given a system described by an open loop transfer fuction L(s), the root locus are all values of s that solve, i.e., are the roots of, the equation
D(s) = 1 + K*L(s) = 0
as the scalar K varies over the range -inf < K < inf. Often the root locus is plotted only for 0 < K < inf ( the default for rlocus() ), but don't forget that sometimes we need to consider K < 0.
That equation is critical becase the roots of D(s) are the closed loop poles of a system with open loop transfer function K*L(s), and the closed loop poles determine the modes of the system. So the root locus technique applies to much more than just dampled oscillator systems, as the example in the Question illustrates with the closed loop poles one the real axis.
  2 个评论
Joel Okanta
Joel Okanta 2022-4-1
Hi Paul, thanks for your response. So after making that comment of root locus being more general I dug a little deeper and found some more information regarding it. In my case, I'm basically using this function to check if I need Closed Loop control for the system I am using, and prove why the root locus shows the instability of my system.
I did see some explanations online which mentioned that instability begins after the roots, whilst stability remains at the roots, but it feels like I am still missing more information
Paul
Paul 2022-4-1
编辑：Paul 2022-4-1
Ran in:
The system in the Question is
Y(s)/U(s) = P(s), where P(s) is:
P = tf([-19008],[960.704 0 -2376000]);
Is this system stable? No, as we can see because it has one pole in the right-half-plane (RHP)
pole(P)
ans = 2×1
49.7311 -49.7311
That means that some sort of feedback control will be needed to stabilize the system. If using proportional control, the root locus of H(s) shows how the closed loop poles migrate as a function of K using compensation of the form u(t) = K*(r(t) - y(t))
figure;
rlocus(P) % default assumption that K > 0
Because one branch of the root locus is always in the RHP, the root locus tells us that proportional control with K > 0 cannot stablize the system.
Plot the root locus for K < 0
figure
rlocus(P,-(0:1000))
This plot tells us that for low, negative K there will be one unstable real closed-loop pole and one stable real closed loop pole. As a critical value of the gain, we have two closed loop poles at the origin and as the gain becomes more negative we have a conjugate pair on the imaginary axis (beause the poles of P are mirror images). Between these two plots (which could have been combined into a single plot) we know that that proportional feedback cannot stabilize the system. Some sort of dynamic compensation is necessary of the form K(s) = k*G(s).
For example, let G(s) = (s + 20)/(s + 80)
G = tf([1 20],[1 80]);
Then we plot the root locus of G*P for k < 0
figure
rlocus(G*P,-1000:0);
The plot shows that for k < kcrit (which is the gain where the red branch crosses the imaginary axis and happens to be ~ -500), the closed loop system with compensation of the form U(s) = (R(s) - Y(s))*K(s), with K(s) = k*G(s), will be stable because all of the branches of the root locus are in the left half plane. Whether or not a particular value of k yields desirable closed loop pole locations is another question.

请先登录，再进行评论。

类别

在 Help Center 和 File Exchange 中查找有关 Classical Control Design 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by