Root Locus system description at given point not showing up

Question

Whitten Oswald 2022-4-5

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1689054-root-locus-system-description-at-given-point-not-showing-up

评论： Y. Shen 2022-11-26

When I use rlocus(), clicking on a point simply displays the coordinates rather than the system information at that point (gain, damping ratio, etc). Additionally, 'grid on' gives an error.

g=tf([1],[1 24 84 80]);

rlocus(g)

Edit: Solved the problem. I was running the code in a live script, but it must be executed in Command Window.

2 个评论
显示无隐藏无

Paul 2022-4-12

Interesting. What happens if you run it in the Live Script, and then click the little arrow in the upper right corner of the figure in the Live script to open it in a figure window? Do the data tips work as expected in that case?

Whitten Oswald 2022-4-13

Nope, that's how I was trying it (in the original screenshot). Same exact code and figure in Command Window works though.

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Pravarthana P 2022-4-8

1
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1689054-root-locus-system-description-at-given-point-not-showing-up#answer_937800

Hi Whitten Oswald,

I understand that you are looking for the system information while hovering over the plot.

In MATLAB versions R2018b or later, the data cursor mode has been made as the built-in interactions. Since you are using R2021b, the data points should be enabled by default.

I tried reproducing the issue at my end and I could see the information datapoints enabled by default. One possible work around would be to customize your built-in interactions and add dataTipInteraction to the Interaction array.

Hope this helps you!!

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

Whitten Oswald 2022-4-8

Thank you for your response.

I discovered the custom DataTips while trying to troubleshoot this problem, but hoped it wouldn't come to that. I'll look into doing this.

请先登录，再进行评论。

Answer 2

Paul 2022-4-8

1
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/1689054-root-locus-system-description-at-given-point-not-showing-up#answer_937985

在 MATLAB Online 中打开

Is there any chance that you have some local version of rlocus() that is shadowing the Control System Toolbox? What is the output of

which rlocus -all
/MATLAB/toolbox/control/ctrlobsolete/rlocus.m
/MATLAB/toolbox/control/ctrldesign/@DynamicSystem/rlocus.m  % Shadowed DynamicSystem method
g=tf([1],[1 24 84 80]);
which rlocus(g)
/MATLAB/toolbox/control/ctrldesign/@DynamicSystem/rlocus.m  % tf method

4 个评论
显示 2更早的评论隐藏 2更早的评论

Whitten Oswald 2022-4-8

No worries, I appreciate you trying anyway. It doesn't seem to be a common problem for a lot of users, so I'll probably just try to implement the data tips manually as Pravarthana P suggested (if I can figure out how).

Thanks again.

Y. Shen 2022-11-26

I have the same problem. I have MATLAB both on my desktop and laptop. On my laptop it shows all the parameters but for some reason the desktop version just shows teh value for x and y axis.

请先登录，再进行评论。