I think you are pretty close from what I can see.
The properties of the app are kept as variables and can be obtained from any callback or function.
I would therefore wait a few lines to set the app.UITable.Data value until you have updated your 'data' variable in the UploadButtonPushed
function UploadButtonPushed(app, event)
[file,path,~]=uigetfile;
app.filename=[path file];
data=readtable(file);
% app.UITable.Data=data;
app.UITable.ColumnName = data.Properties.VariableNames;
data.Properties.VariableNames{1}='Load mass';
data.Properties.VariableNames{2}='RBB';
data.Properties.VariableNames{3}='LBB';
data.Properties.VariableNames{4}='RES';
data.Properties.VariableNames{5}='LES';
app.UITable.Data=data; % Save data in app after setting variable names
% Not used in this function - could be removed from here to 'end'
x = table2array(data(:,"Load mass"));
y = table2array(data(:,"RBB"));
y2=table2array(data(:,"LBB"));
y3=table2array(data(:,"RES"));
y4=table2array(data(:,"LES"));
R = rmmissing(x);
R1 = rmmissing(y);
R2 = rmmissing(y2);
R3 = rmmissing(y3);
R4 = rmmissing(y4);
end
And then I'd refrain from loading data again in the other callbacks by reusing the data from the table
function PlotButtonPushed(app, event)
data=app.UITable.Data;
x = table2array(data(:,"Load mass"));
y = table2array(data(:,"RBB"));
y2=table2array(data(:,"LBB"));
y3=table2array(data(:,"RES"));
y4=table2array(data(:,"LES"));
plot(app.UIAxes,x,y,x,y2,x,y3,x,y4);
title(app.UIAxes, 'Load Mass vs ALL')
xlabel(app.UIAxes, 'Load Mass')
ylabel(app.UIAxes, 'All')
legend(app.UIAxes,'RBB','LBB','RES','LES');
end
And similarly the MPButtonPushed as (unless you define x, y, R etc. as public properties and access them by app.x rather than x, which would be slightly more efficient)
function MPButtonPushed(app, event)
data=app.UITable.Data;
x = table2array(data(:,"Load mass"));
y = table2array(data(:,"RBB"));
y2=table2array(data(:,"LBB"));
y3=table2array(data(:,"RES"));
y4=table2array(data(:,"LES"));
R = rmmissing(x);
R1 = rmmissing(y);
R2 = rmmissing(y2);
R3 = rmmissing(y3);
R4 = rmmissing(y4);
themean=mean(R);
themean1= mean(R1);
themean2= mean(R2);
themean3= mean(R3);
themean4= mean(R4);
m = sum((x - themean).*(y- themean1));
p = sum((x - themean).*(x - themean));
l1 = m/p;
%%LBB MP
m2 = sum((x - themean).*(y2 - themean2));
l2 = m2/p;
%%RES MP
m3 = sum((x - themean).*(y3 - themean3));
l3 = m3/p;
%%LES MP
m4 = sum((x - themean).*(y4 - themean4));
l4 = m4/p;
c = categorical({'RBB','LBB','RES','LES'});
title(app.UIAxes, 'MP')
xlabel(app.UIAxes, 'Type')
ylabel(app.UIAxes, 'Cycle')
bar(app.UIAxes, c, [l1;l2;l3;l4],'LineWidth',0.4);
end
You could make several minor optimisations e.g. by adding a filter to your uigetfile and by adding a StartUpFcn to disable the Plot and MP buttons until you have loaded data, but that's just bells and whistles - I think the above code will implement your minimum requirements
