清空筛选条件
清空筛选条件

Running into error when using pwelch for FFT

25 次查看（过去 30 天）
Benjamin Colbert
Benjamin Colbert 2022-5-7
评论： George about 18 hours 前
I am trying to conduct a FFT on a wav file in order to then calculate SPL within a bandwidth (120-450hz). I am using code from another answered question and I get hung up on an error:
Error using signal.internal.spectral.welchparse>segment_info
The length of the segments cannot be greater than the length of the input signal.
Error in signal.internal.spectral.welchparse (line 34)
[L,noverlap,win] = segment_info(M,win1,noverlap1);
Error in welch (line 55)
signal.internal.spectral.welchparse(x,esttype,args{:});
Error in pwelch (line 170)
[welchOut{1:nargout}] = welch(x,funcName,inputArgs{:});
Error in snip_extractor (line 16)
[sensor_spectrum, freq] = pwelch(samples,w,NOVERLAP,NFFT,Fs);
My code follows. I am loading a 30sec wav file and then selecting a 5sec period with the file for analysis. Any help here would be most appreciated:
[y,Fs]=audioread('67649542.060120201700.wav') %Load fullfile
snips = y([163840:327680], [1]) %Extract data from period of interest
%%%Borrowed code from https://www.mathworks.com/matlabcentral/answers/636155-plotting-fft-for-audio-wav-file
NFFT = (Fs/2);
NOVERLAP = round(0.75*NFFT);
w = hanning(NFFT);
samples = length(snips)
dt = 1/Fs
t = (0:dt:(samples-1)*dt)
[sensor_spectrum, freq] = pwelch(samples,w,NOVERLAP,NFFT,Fs);
sensor_spectrum_dB = 20*log10(sensor_spectrum);
figure(1),semilogx(freq,sensor_spectrum_dB);grid
title(['Averaged FFT Spectrum / Fs = ' num2str(Fs) ' Hz / Delta f = ' num2str(freq(2)-freq(1)) ' Hz ']);
xlabel('Frequency (Hz)');ylabel(my_ylabel);
  4 个评论
显示 2更早的评论
Jonas
Jonas 2022-5-8
is there a reason for re 1*10^-6 Pa and not 20*10^-6 Pa?
do you want to calculate one SPL value for one file in your frequency range or do you want to extract multiple SPL values over time for each file?
George
George about 18 hours 前
Referencing to 1*10^-6 Pa is used for underwater signals.
That is SPL re 1 micro Pascal @ 1m @ 1W
Whereas yoru second reference, that is, 20 micro Pascals is used for referencing signal thresholds in air where it is generally acknowldeged that a normal average listener's threshold of hearing is 20 micro Pascals.

请先登录，再进行评论。

请先登录，再回答此问题。

回答（1 个）

Jonas
Jonas 2022-5-7
编辑：Jonas 2022-5-7
[
sensor_spectrum, freq] = pwelch(samples,w,NOVERLAP,NFFT,Fs);
should be
[sensor_spectrum, freq] = pwelch(snips,w,NOVERLAP,NFFT,Fs);
since samples is only a scalar and not your data vector
the displayed error says, that your window of length fs/2 is lager than the given data vector, which is 1x1 by mistake

类别

在 Help Center 和 File Exchange 中查找有关 Fourier Analysis and Filtering 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by