AD-FMCOMMS5 using MATLAB SD card image RX tuning failed!

1 次查看(过去 30 天)
Hello All,
I imaged the SD card from ZYNQ communication tool box setup.
I'm getting this error in the reported data at the UART console after boot up:
[ 436.350902] SAMPL CLK: 3000000 tuning: RX
[ 436.354901] 0:1:2:3:4:5:6:7:8:9:a:b:c:d:e:f:
[ 436.359287] 0:# # # # # # # # # # # # # # # #
[ 436.363829] 1:# # # # # # # # # # # # # # # #
[ 436.368263] ad9361 spi32766.1: ad9361_dig_tune_delay: Tuning RX FAILED!
[ 437.416787] SAMPL CLK: 3000000 tuning: RX
[ 437.420761] 0:1:2:3:4:5:6:7:8:9:a:b:c:d:e:f:
[ 437.425175] 0:# # # # # # # # # # # # # # # #
[ 437.429599] 1:# # # # # # # # # # # # # # # #
[ 437.434037] ad9361 spi32766.1: ad9361_dig_tune_delay: Tuning RX FAILED!
[ 438.484925] mwipcore 43c50000.mwbypassrx: [MMAP] size:10000 pgoff: 0
[ 438.491554] mwipcore 43c50000.mwbypassrx: Simple VMA close.
[ 438.664892] mwipcore 43c50000.mwbypassrx: [MMAP] size:10000 pgoff: 0
[ 438.671518] mwipcore 43c50000.mwbypassrx: Simple VMA close.
[ 441.938035] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.947493] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.957100] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.966586] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.976106] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.986524] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.102520] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.112013] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.122675] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.133221] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.143705] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.154185] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.280004] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.291991] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
Any help is highly appreciated!
Kind Regards
Arash

回答(0 个)

产品


版本

R2021a

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by