AD-FMCOMMS5 using MATLAB SD card image RX tuning failed!

1 次查看（过去 30 天）
Arash Jafari
Arash Jafari 2022-6-28
Hello All,
I imaged the SD card from ZYNQ communication tool box setup.
I'm getting this error in the reported data at the UART console after boot up:
[ 436.350902] SAMPL CLK: 3000000 tuning: RX
[ 436.354901] 0:1:2:3:4:5:6:7:8:9:a:b:c:d:e:f:
[ 436.359287] 0:# # # # # # # # # # # # # # # #
[ 436.363829] 1:# # # # # # # # # # # # # # # #
[ 436.368263] ad9361 spi32766.1: ad9361_dig_tune_delay: Tuning RX FAILED!
[ 437.416787] SAMPL CLK: 3000000 tuning: RX
[ 437.420761] 0:1:2:3:4:5:6:7:8:9:a:b:c:d:e:f:
[ 437.425175] 0:# # # # # # # # # # # # # # # #
[ 437.429599] 1:# # # # # # # # # # # # # # # #
[ 437.434037] ad9361 spi32766.1: ad9361_dig_tune_delay: Tuning RX FAILED!
[ 438.484925] mwipcore 43c50000.mwbypassrx: [MMAP] size:10000 pgoff: 0
[ 438.491554] mwipcore 43c50000.mwbypassrx: Simple VMA close.
[ 438.664892] mwipcore 43c50000.mwbypassrx: [MMAP] size:10000 pgoff: 0
[ 438.671518] mwipcore 43c50000.mwbypassrx: Simple VMA close.
[ 441.938035] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.947493] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.957100] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.966586] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.976106] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 441.986524] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.102520] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.112013] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.122675] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.133221] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.143705] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.154185] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.280004] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
[ 442.291991] mmcblk0: response CRC error sending r/w cmd command, card status 0x900
Any help is highly appreciated!
Kind Regards
Arash

请先登录，再回答此问题。

回答（0 个）

类别

在 Help Center 和 File Exchange 中查找有关 Targeting FPGA & SoC Hardware 的更多信息

标签

产品


版本

R2021a

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by