How can I replace System Toolbox, like phased.ULA() and phased.Pha​seShiftBea​mformer(), by pure Matlab code?

3 次查看（过去 30 天）
Weichun
Weichun 2023-12-7
回答： Sarthak 2023-12-21
Hi, everyone!
I'm doing a Matlab project, the aim of this project is to remove system toolbox, only use pure Matlab code. there are two system toolbox, I have no idea how to replace them. I pasted the code below:
clear all;
retVal = 1.0e+03 * [
3.5040 - 0.0300i, 3.6100 + 2.9130i;
-0.6230 + 0.0330i, -1.0960 + 1.2770i;
1.6360 - 1.1560i, 2.4620 + 2.2290i;
4.4610 + 2.9620i, 3.8240 + 6.1530i
];
c=3e8;
fc=77e9;
lambda=c/fc;
Ne = 4;
rxArray = phased.ULA('NumElements',Ne,'ElementSpacing',lambda/2);
% Form forward-facing beam
beamformer = phased.PhaseShiftBeamformer('SensorArray',rxArray,...
'PropagationSpeed',c,'OperatingFrequency',fc,'Direction',[0;0]);
% Beamform received data
Xbf = beamformer(retVal');
disp(Xbf);
I want to remove phased.ULA() and phased.PhaseShiftBeamformer(), and rewrite them with only pure Matlab code. I would greatly appreciate it if anyone can help? I have write some code to replace phased.ULA(), I pasted below:
clear all;
% Provided data
retVal = 1.0e+03 * [
3.5040 - 0.0300i, 3.6100 + 2.9130i;
-0.6230 + 0.0330i, -1.0960 + 1.2770i;
1.6360 - 1.1560i, 2.4620 + 2.2290i;
4.4610 + 2.9620i, 3.8240 + 6.1530i
];
c = 3e8;
fc = 77e9;
lambda = c / fc;
Ne = 4;
% Manually simulate ULA array response
theta = 0:pi/180:2*pi; % Angle range
element_positions = zeros(3, Ne);
for n = 1:Ne
element_positions(1, n) = 0; % x-coordinate
element_positions(2, n) = (n - (Ne+1)/2) * lambda/2; % y-coordinate
element_positions(3, n) = 0; % z-coordinate
end
Until now, I have no idea how to continue replacing phased.PhaseShiftBeamformer().

请先登录，再回答此问题。

回答（1 个）

Sarthak
Sarthak 2023-12-21
Hi Weichun,
The phased.PhaseShiftBeamformer object implements a narrowband phase-shift beamformer. If you want to implement this with only MATLAB code; you can go through the following paper by IEEE.
https://ieeexplore.ieee.org/document/6526910
They have explained the design for a narrowband phase-shift beamformer step by step and all results were generated in MATLAB. I think this should help you rewrite phased.PhaseShiftBeamformer in MATLAB.

类别

在 Help Center 和 File Exchange 中查找有关 Array Geometries and Analysis 的更多信息

标签

产品


版本

R2023b

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by