Hello. If I have included delays in my code for my controller, how do I implement it so that the delays are considered when the code is executed?

Question

Danikha Shyken 2023-12-13

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2060034-hello-if-i-have-included-delays-in-my-code-for-my-controller-how-do-i-implement-it-so-that-the-del

回答： Joel Van Sickel 2024-1-3

this is the simulink model where the buck-boost controller is connected to the gate ports of each switch to power up the converter. And Im thinking that the delays in my code are not considered when the code is executed because the ouput if too low

2 个评论
显示无隐藏无

Danikha Shyken 2023-12-13

在 MATLAB Online 中打开

function [q1, q2, q3, q4, duty_cycle] = buckBoostController(vin)
    q1 = 0;
    q2 = 0;
    q3 = 0;
    q4 = 0;
    duty_cycle = 0;
    delay = 0;
    % Define the duty cycle and delay values for each case of input voltage
    if vin == 0.6
        duty_cycle = 0.6667;
        delay = 5e-7*(240.012)/360;
    elseif vin == 0.77
        duty_cycle = 0.7004;
        delay = 5e-7*(252.144)/360;
    elseif vin == 1.2
        duty_cycle = 0.6000;
        delay = 5e-7*(216)/360;
    elseif vin == 2
        duty_cycle = 0.4737;
        delay = 5e-7*(170.532)/360;
    end
    % Calculate the duty cycles for q1, q2, q3, and q4 based on the input voltage and duty cycle
    if vin == 2
        % Operate in Buck Mode
        q1 = duty_cycle;
        q2 = 0;
        q3 =1-duty_cycle;
        q4 = 1.8;
    elseif vin == 1.8
        % Operate in Battery Voltage Mode
        q1 = 1.8;
        q2 = 0;
        q3 = 0;
        q4 = 0;
    else
        % Operate in Boost Mode or Battery Voltage Mode
        q1 = 1.8;
        q2 = duty_cycle;
        q3 = 0;
        q4 = 1-duty_cycle;
    end
end

Danikha Shyken 2023-12-13

the code above is the code for the buck-boost controller

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Joel Van Sickel 2024-1-3

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2060034-hello-if-i-have-included-delays-in-my-code-for-my-controller-how-do-i-implement-it-so-that-the-del#answer_1382376

The correct way to simulate a digital controller, so that you are incorporating the delay of the digital system is to utilize some of our discrete time simulation capabilities. I would recommend declaring a variable ts (any name will do) that you set to the update rate of your digital system that the code is running on. Then on all the inputs to the digital system, place a zero order hold block with time step of ts, then at the output of the digital system, place a unit delay with the same ts value. This will simulate the delay of the digital system. However, what you are doing is a bit more sophisticated, so you might want to use this block instead, it will simulate slower, but will give you more control over the signal: https://www.mathworks.com/help/simulink/slref/variabletimedelay.html

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Hello. If I have included delays in my code for my controller, how do I implement it so that the delays are considered when the code is executed?

2 个评论
显示无隐藏无

回答（1 个）

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

另请参阅

类别

标签

Community Treasure Hunt

Hello. If I have included delays in my code for my controller, how do I implement it so that the delays are considered when the code is executed?

2 个评论 显示 无隐藏 无

回答（1 个）

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

另请参阅

类别

标签

Community Treasure Hunt

2 个评论
显示无隐藏无

0 个评论
显示 -2更早的评论隐藏 -2更早的评论