清空筛选条件
清空筛选条件

There are problems when matlab and amesim jointly defend

7 次查看（过去 30 天）
昱绮
昱绮 2023-12-15
编辑： Aiswarya 2024-2-21
Reinforcement learning is a problem that occurs when the s-function of amesim is invoked in the co-simulation of matlab and amesim
警告: Fast Restart mode cannot be enabled for model 'untitled1' for the following reasons:
警告: Fast Restart mode relies on the ability to save the model's operating point. However, the following error occurred when an attempt was made to save the operating point:
警告: Simulink is unable to save the operating point of the C Level-2 S-Function (testnew_) block 'untitled1/testnew2/S-Function' because the S-function has pointer work (PWork) vectors.
  1 个评论
cm s
cm s 2024-2-20
朋友你好，请问你解决这个问题了吗？我的也是matlab与amesim联仿进行强化学习方面的研究。我的程序和你有一样的“警告”，是可以跑，但跑起来在amesim中没任何数据产生，很苦恼，我检查了很多地方，怀疑就这三个“警告”的问题。可以的话，希望与你交流一下，可以有偿

请先登录，再进行评论。

请先登录，再回答此问题。

回答（1 个）

Aiswarya
Aiswarya 2023-12-19
编辑：Aiswarya 2024-2-21
嗨，我将用英语回答这个问题。
I see that you are trying to save the operating point of a model which involves S-functions. The error you are getting is because of Operating Point Compliance which handles S-function operating point information when saving the model operating point. In the error it shows that your S-function has pointer work (Pwork) vectors. When you use PWorks without explicitly specifying the operating point compliance, the compliance becomes DISALLOW_OPERATING_POINT after compilation. For this setting, the S-function does not allow saving or restoring its operating point and the software issues an error.
This error can be resolved by changing the OperatingPointCompliance in the S-function using ssSetOperatingPointCompliance (https://www.mathworks.com/help/simulink/sfg/sssetoperatingpointcompliance.html?searchHighlight=OperatingPointCompliance&s_tid=srchtitle_support_results_1_OperatingPointCompliance). The appropriate setting for S-functions that use Pwork vectors is 'USE_CUSTOM_OPERATING_POINT'. You can change this setting inside the 'mdlInitializeSizes' function of your S-function as follows:
ssOperatingPointCompliance setting = USE_CUSTOM_OPERATING_POINT;
ssSetOperatingPointCompliance(S, setting);
If you want to access the operating point information for your S-function in the 'Simulink.op.ModelOperatingPoint' object for the model you have to also enable the 'OperatingPointVisibility'.
boolean_T visibility = true;
ssSetOperatingPointVisibility(S, visibility);
You may refer to the following example : https://www.mathworks.com/help/simulink/sfg/sssetoperatingpointcompliance.html?searchHighlight=OperatingPointCompliance&s_tid=srchtitle_support_results_1_OperatingPointCompliance#mw_b0e7c464-99c7-4374-b223-73d9be5e8bde

类别

在 Help Center 和 File Exchange 中查找有关 Debug and Analyze Quality of S-Functions 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by