I want to design the loss calculation model of three phase inverter and loss calculation of the motor using the FEM Parameterized PMSM

Question

Kashif Habib 2024-2-5

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2078131-i-want-to-design-the-loss-calculation-model-of-three-phase-inverter-and-loss-calculation-of-the-moto

回答： Kashif Habib 2024-2-11

I am designing the three phase inverter having both the loss calculation of the inverter and motor.

While simulating i am getting an error.

Error compiling Simscape network for model PMSM_MOSFET_2.

Caused by:

Frequency and time simulation is not applicable because sinusoidal expressions are not used by any other equations and have been eliminated.
Check variable intrm_sf_mf__2.
Check variable intrm_sf_mf__3.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Sabin 2024-2-6

Frequency-and-time equation formulation is intended for systems with a single nominal frequency. It is not possible to simulate switching devices such as MOSFETs. When designing the electric drive and power inverter you should set the 'Equation formulation' to 'Time' in the Solver Configuration block.

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

Kashif Habib 2024-2-7

Thanks Professor, but after making the solver configuration block to "Time". I am getting this error....

An error occurred while running the simulation and the simulation was terminated

Caused by:

['PMSM_MOSFET_2/Solver Configuration']: At time 0.000300, one or more assertions are triggered. See causes for specific information.
In divide, the denominator must be nonzero. The assertion comes from: Block path: PMSM_MOSFET_2/FEM-Parameterized PMSMAssert location: o (location information is protected)
In divide, the denominator must be nonzero. The assertion comes from: Block path: PMSM_MOSFET_2/FEM-Parameterized PMSMAssert location: o (location information is protected)
In divide, the denominator must be nonzero. The assertion comes from: Block path: PMSM_MOSFET_2/FEM-Parameterized PMSMAssert location: o (location information is protected)

Thanks

请先登录，再进行评论。

Answer 2

Kashif Habib 2024-2-11

I am designing the three phase inverter having both the loss calculation of the inverter and motor.

While simulating i am getting an error.

An error occurred while running the simulation and the simulation was terminated

Caused by:

['PMSM_MOSFET_2/Solver Configuration']: At time 0.000300, one or more assertions are triggered. See causes for specific information.
In divide, the denominator must be nonzero. The assertion comes from: Block path: PMSM_MOSFET_2/FEM-Parameterized PMSMAssert location: o (location information is protected)
In divide, the denominator must be nonzero. The assertion comes from: Block path: PMSM_MOSFET_2/FEM-Parameterized PMSMAssert location: o (location information is protected)
In divide, the denominator must be nonzero. The assertion comes from: Block path: PMSM_MOSFET_2/FEM-Parameterized PMSMAssert location: o (location information is protected)

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

I want to design the loss calculation model of three phase inverter and loss calculation of the motor using the FEM Parameterized PMSM

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

回答（2 个）

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

另请参阅

类别

标签

产品

版本

Community Treasure Hunt

I want to design the loss calculation model of three phase inverter and loss calculation of the motor using the FEM Parameterized PMSM

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

回答（2 个）

1 个评论 显示 -1更早的评论隐藏 -1更早的评论

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

另请参阅

类别

标签

产品

版本

Community Treasure Hunt

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

1 个评论
显示 -1更早的评论隐藏 -1更早的评论

0 个评论
显示 -2更早的评论隐藏 -2更早的评论