how to change variable value in lookup table during simulation in Simulink?

6 次查看（过去 30 天）

Mounira 2024-2-20

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2084353-how-to-change-variable-value-in-lookup-table-during-simulation-in-simulink

编辑： Fangjun Jiang 2024-2-21

Hello,

so I have a 2 table lookup; first table has: P (48 values) and time(1:1:48); and the second table has: load Q (48 values) and time(1:1:48);

at some time ; for example at time=6; i want to change the value of P to 9; how can change variable value at the same time of simulation running?

I tried to use Matlab function to change the value of P but it didn't work;

the code is:

function Pref= fcn(loadref,currenttime, P )

persistent loadrefold;

% Initialize persistent variable

if isempty(loadrefold)

loadrefold = 0;

end

if loadref ~= loadrefold;

updatetime = round(currenttime+1)

P(updatetime,1)=loadref;

loadrefold=loadref;

Pref=P;

else Pref=P;

end

2 个评论
显示无隐藏无

Sam Chak 2024-2-20

Hi @Mounira

Based on your clear description, it seems that there are two Lookup Tables involved. You mentioned that each Lookup Table has two inputs to the block, one being the load and the other being the time. However, I only see the time input (Hour of the Day) in the Simulink model. Am I missing something?

Additionally, at time

, you mentioned that you want to set the value of Load to 9, which seems to be a fixed value not dependent on the Lookup Table. Do you intend for the Load to remain at 9 for time t > 6 until the end of the simulation?

jana nassereddine 2024-2-20

i have inside the lookup table; i have 2 inputs; i will show you a picture; as for th etime; no only for a specific time i want a specific value;

请先登录，再进行评论。

请先登录，再回答此问题。

回答（2 个）

Jon 2024-2-20

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2084353-how-to-change-variable-value-in-lookup-table-during-simulation-in-simulink#answer_1412713

You could use the step block, found under Simulink>Sources for this purpose

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Fangjun Jiang 2024-2-20

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2084353-how-to-change-variable-value-in-lookup-table-during-simulation-in-simulink#answer_1412738

Usually, using Dashboard blocks allow you to change variable values interactively during simulation

https://www.mathworks.com/help/simulink/slref/horizontalslider.html

7 个评论
显示 5更早的评论隐藏 5更早的评论

Fangjun Jiang 2024-2-20

Look at your question and title, where does MPC come from??

Fangjun Jiang 2024-2-21

If the value of "P" is created or modified by this MPC or the MATLAB function, then this solution would be perfect too. Make that "P" an output of this MPC or the MATLAB Function block, remove the Constant block, feed "P" to the "T" port of the 1-D Lookup Table block, making it a dynamic lookup table.

请先登录，再进行评论。

请先登录，再回答此问题。