Thingspeak channel inconsistant data

Question

bader 2024-4-15

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2107221-thingspeak-channel-inconsistant-data

编辑： Swastik Sarkar 2024-5-21

Dear All,

Thingspeak channel got two entries of data and then stopped receiving any new entries. my project consist from the following equipment, Arduino Uno where it have both Current and Voltage sensors, alongside Esp8266 NodeMcu that is receiving Arduino's data as a serial connection, and lastly Thngspeak channel that will display the serial data gathered by ESP8266 NodeMcu. Because the needed data is being transferred via serial connection , there is a JSON object to parse the data. instead of using Tx and Rx Pins on both Arduino and Esp8266 the project have Pin 10 and 11 on the Arduino side and Pin 5 and 6 on the Esp8266 Side. Thngspeak somehow just detected two entries of data and the delay between were much much more than what is coded. while on serial monitor Arduino works perfectly fine in contrast from ESP8266 where it connect to the established WIFI network but not Thngspeak server.

Esp8266 side code

//Include Lib for Arduino to Nodemcu
#include <SoftwareSerial.h>
#include <ArduinoJson.h>
//Wifimodule and thingspeak lib
#include <ESP8266WiFi.h>  //Link in description
#include <ThingSpeak.h>
//D6 = Rx & D5 = Tx
SoftwareSerial nodemcu(D6, D5);
//Timer - milliseconds
unsigned long previousMillis = 0;
unsigned long currentMillis;
const unsigned long period = 150000;
//Variable for data
float voltageValue;
float currentValue;
float powerValue;
//Wifi related variables
String apiKey = "GWAAHMFKOZZKVADI";  //Write API key
unsigned long channelID = 2507368;
const char *ssid = "TP-Link_ADE8";
const char *pass = "27621332";
const char *server = "api.thingspeak.com";
//Boolean Variables
boolean state1 = false;
boolean state2 = false;
WiFiClient client;
//-------------------------------------------------- SETUP ------------------------------------------------------------
void setup() {
  Serial.begin(9600);
  nodemcu.begin(9600);
  ThingSpeak.begin(client);
  while (!Serial) continue;
  delay(1000);
  Serial.println("Program Started");
  //Establish WiFi Connection
  wifi_connect();
}
//-------------------------------------------------- LOOP ------------------------------------------------------------
void loop() {
  //Get current time
  currentMillis = millis();
  if ((currentMillis - previousMillis >= period)) {
    //Check if connected to WiFi, else connect
    if (WiFi.status() != WL_CONNECTED) {
      wifi_connect();
    } else {
      Serial.println("Currently Connected to WiFi");
    }
    //Connect to Thingspeak and push data
    while (state1 == false) {
      while (state2 == false) {
        parseJsonObject();
      }
      cloud_connect();
    }
    state1 = false;
    state2 = false;
    Serial.println("Cloud Connect Succesful");
    Serial.println("-----------------------------------------");
    previousMillis = previousMillis + period;
  }
}
//----------------------------------------- FUNCTION - WiFi Connect -----------------------------------------
void wifi_connect() {
  Serial.println("Connecting to ");
  Serial.println(ssid);
  WiFi.begin(ssid, pass);
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("");
  ThingSpeak.begin(client);
  Serial.println("WiFi Connected");
}
//------------------------------------------ FUNCTION Cloud Connect -----------------------------------------
void cloud_connect() {
  //"184.106.153.149" or api.thingspeak.com
  if (client.connect(server, 80)) {
    String postStr = apiKey;
    postStr += "&field1=";
    postStr += String(currentValue);
    postStr += "&field2=";
    postStr += String(voltageValue);
    postStr += "&field3=";
    postStr += String(powerValue);
    postStr += "\r\n\r\n\r\n";
    client.print("POST /update HTTP/1.1\n");
    client.print("Host: api.thingspeak.com\n");
    client.print("Connection: close\n");
    client.print("X-THINGSPEAKAPIKEY: " + apiKey + "\n");
    client.print("Content-Type: application/x-www-form-urlencoded\n");
    client.print("Content-Length: ");
    client.print(postStr.length());
    client.print("\n\n\n");
    client.print(postStr);
    Serial.print("Current: ");
    Serial.print(currentValue);
    Serial.print(" || Voltage: ");
    Serial.println(voltageValue);
    Serial.print(" || Power: ");
    Serial.print(powerValue);
    Serial.println("Sent to Thingspeak");
    //Change state to true to break while loop
    state1 = true;
  }
  client.stop();
}
void parseJsonObject() {
  //Parse JSON object from serial port
  StaticJsonDocument<1000> doc;
  DeserializationError error = deserializeJson(doc, nodemcu);
  Serial.println("Received JSON Data:");
Serial.println(nodemcu.readString());
  // Test if parsing succeeds
  if (error) {
    Serial.println("deserializeJson error");
    return;
  }
  //Parse Json values and store in variable
  voltageValue = doc["Voltage"];
  currentValue = doc["Current"];
  powerValue = doc["Power"];
  //ldr = doc["ldr"];
  if (isnan(voltageValue) || isnan(currentValue) || isnan(powerValue) || voltageValue == 0.0 || currentValue == 0.0 || powerValue == 0.0) {
    Serial.println("Invalid Sensor Readings");
    return;
  }
  state2 = true;
  Serial.println("JSON Object Recieved");
}

Arduino Code

//Arduino side code
//DHT11 Lib
//#include <DHT.h>
//Watchdog Timer
#include <avr/wdt.h>
//Arduino to NodeMCU Lib
#include <SoftwareSerial.h>
#include <ArduinoJson.h>
//Initialise Arduino to NodeMCU (10=Rx & 11=Tx)
SoftwareSerial nodemcu(10, 11);
/*Initialisation of DHT11 Sensor
#define DHTPIN 4
DHT dht(DHTPIN, DHT11);
float temp;
float hum;*/
int VoltageSensorPin = A0;  // Declaring Pin used with Voltage Sensor
int CurrentSensorPin = A1;  // Declaring Pin used with Current Sensor
float voltageValue = 0.0;   // decalring the output voltage label, this is the voltage reading sent from the load to the voltage sensor
float currentValue = 0.0;   // declaring the output current label, this is the current reading sent from the load to the current sensor
float powerValue = 0.0; 
void setup() {
  Serial.begin(9600);
 // dht.begin();
  nodemcu.begin(9600);
  delay(1000);
  //Enable Watchdog timer
  wdt_enable(WDTO_4S);
  Serial.println("Program started");
}
void loop() {
  StaticJsonDocument<1000> doc;
  //Obtain Temp and Hum data
  reading_func();
 
  //Assign collected data to JSON Object
  doc["Voltage"] = voltageValue;
  doc["Current"] = currentValue;
  doc["Power"] = powerValue;
  
  //Send data to NodeMCU
  serializeJson(doc, nodemcu);
  //Reset for WDT
  wdt_reset();
}
void reading_func() {
    const float R1 = 30000.0;       // this is a fixed resistor value embeded onto the voltage sensor
  const float R2 = 7500.0;        // this is a fixed resistor value embeded onto the voltage sensor
  float ref_voltage = 5.0;        // Float for Reference Voltage
  const float SensavityI = 0.66;  // this is a fixed value embeded onto the current sensor due to being 30A sensor
  const float offsetI = 2.5;      // Voltage measurement if Taking the measurment from Vin and Out of Current sensor
  float VasBinary = 0.0;          // the representation of measured  voltage reading as a Voltage
  float IasBinary = 0.0;          // the representation of measured current reading as a Voltage
  float Samples = 0.0;
  float average = 0.0;           // the average of detected values after sampling
  float IDetectedReading = 0.0;  // the measurement that is sent to Arduino
  float VDetectedReading = 0.0;  // the measurement that is sent to Arduino
  Samples = 0.0;  // Reset Samples to 0 for each loop iteration
  for (int x = 0; x < 150; x++) {  //Get 150 samples to provide stebility
    IDetectedReading = analogRead(CurrentSensorPin);
    Samples = Samples + IDetectedReading;
    delay(3);
  }
  average = Samples / 150.0;               //Taking Average of Samples
  IasBinary = (average * (5.0 / 1024.0));  // Converting detected measurment from Analog to Digital
  currentValue = ((offsetI - IasBinary) / SensavityI);
  if (currentValue > -0.000005 && currentValue < 0.000005) {
    currentValue = 0;
  } else {
    currentValue = currentValue - 0.185;  // this is to remove the internal offset current after conversion from voltage
  }
  VDetectedReading = analogRead(VoltageSensorPin);
  VasBinary = (VDetectedReading * ref_voltage) / 1024.0;  // Converting detected measurment from Analog to Digital
  voltageValue = VasBinary * ((R1 + R2) / R2);            // Reverting the measurment from voltage sensor to the Real value of the physical componant by invert voltage devider ratio
  powerValue = voltageValue * currentValue;  // P = VI
  Serial.print("Input Voltage = ");
  Serial.println(voltageValue, 2);
 // Serial.print("Raw Sensor Value = ");
 // Serial.print(VDetectedReading);
 // Serial.print("\t Voltage = ");
 // Serial.print(IDetectedReading, 3);
  Serial.print("\t Current = ");
  Serial.println(currentValue, 7);
  Serial.print("\t Power = ");
  Serial.println(powerValue, 3);
  delay(15000);
  /*hum = dht.readHumidity();
  temp = dht.readTemperature();
  Serial.print("Humidity: ");
  Serial.println(hum);
  Serial.print("Temperature: ");
  Serial.println(temp);*/
  if (isnan(voltageValue) || isnan(currentValue) || isnan(powerValue) || voltageValue == 0.0 || currentValue == 0.0 || powerValue == 0.0) {
    while (1) {}
  }
}

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Swastik Sarkar 2024-5-21

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/2107221-thingspeak-channel-inconsistant-data#answer_1460716

编辑：Swastik Sarkar 2024-5-21

Hi @bader,

I noticed that you are attempting to send data to the ThingSpeak server at intervals of 150,000 milliseconds, but ThingSpeak seems to only register 2 entries, possibly spaced out by 5 minutes (300,000 milliseconds). This discrepancy suggests there might be an issue with the "cloud_connect" function, as the rest of your code appears to be correctly implemented.

To address this issue, instead of manually crafting the HTTP request, consider utilizing the “thingSpeakWrite” function, which is designed for integrating with ThingSpeak more efficiently. This function also offers the ability to specify timestamps, potentially aligning better with the needs of the application.

You can find detailed guidance on using “thingSpeakWrite” in the MathWorks documentation here: https://www.mathworks.com/help/thingspeak/thingspeakwrite.html

For Arduino projects, the corresponding function is "ThingSpeak.writeField," which is included in the ThingSpeak Arduino library. You can access detailed instructions and examples in its documentation on GitHub here: https://github.com/mathworks/thingspeak-arduino/blob/master/README.md#writefield

Hope this helps.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

Thingspeak channel inconsistant data

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

回答（1 个）

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

社区

另请参阅

类别

标签

Community Treasure Hunt

Thingspeak channel inconsistant data

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

回答（1 个）

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

社区

另请参阅

类别

标签

Community Treasure Hunt

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

0 个评论
显示 -2更早的评论隐藏 -2更早的评论