Could someone perhaps guide me in the right direction to figure out a way to start this code?

Question

Collin Kerr 2016-4-21

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/280272-could-someone-perhaps-guide-me-in-the-right-direction-to-figure-out-a-way-to-start-this-code

评论： Collin Kerr 2016-4-28

(Assignment) "Your program should also have a feature that predicts the velocities and elevation angles at which the projectile can be launched to hit a target given a specified distance. The input to this part of the program should be only the target distance. The output from this part of the program should be the velocities and launch angles for the projectile."

I don't see a way to get both those outputs by just inputting a distance. I'm not asking for someone to give me a code, but just a something to help me start.

3 个评论
显示 1更早的评论隐藏 1更早的评论

James Tursa 2016-4-21

编辑：James Tursa 2016-4-21

I assume you have been studying projectile motion in class. So what equations are you familiar with for this motion? Forget the targeting aspects for the moment ... if you were simply given a velocity and an angle, could you write a program to predict its trajectory? Start with that. Once you have that working, then it shouldn't be too much work to extend it to a targeting program. See this link:

https://en.wikipedia.org/wiki/Projectile_motion

Collin Kerr 2016-4-21

编辑：Walter Roberson 2016-4-21

在 MATLAB Online 中打开

clc,clear
F = input('Targeted Distance = ');
V_o = input('Velocity at launch = ');
Theta = input('Elevation angle at launch = ');
a=-9.81;                     %Its a given
b=V_o*sind(Theta)             %It makes the coding a bit less confusing.
c=0;                        %Also a given
      fprintf('The targeted distance for the launch is %d meters. \n', F)
      fprintf('The velocity for the launch is %d meters per second. \n', V_o)
      fprintf('The elevation angle for the launch is %d degrees. \n', Theta);
   Q1=(-b-sqrt(b^2-4*a*c))/(a);       %The 1/2 and times 2 cross out for the denom
   disp(Q1)
   %%Horizontal Range
H = V_o*cosd(Theta)*(Q1);
    fprintf('The Horizontal Range of the launch is %0.3f \n', H)
%%Vertical Height
V = (b^2)/(a*2)*2;
    fprintf('The Vertical Height of the launch is %0.3f \n', V)

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Arnab Sen 2016-4-25

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/280272-could-someone-perhaps-guide-me-in-the-right-direction-to-figure-out-a-way-to-start-this-code#answer_219271

在 MATLAB Online 中打开

Hi Collin,

In this case there would be multiple velocity and launch angles. The formulae for projectile distance is

d=(v^2/g). sin(2.theta).

where v is initial velocity, g gravitational acceleration and theta is projection angle.

Now if d is given, then relation between v and theta will be,

v=sqrt(d.g.cosec(2.theta)).

Now, you can vary the theta from 1 to 90 degree in specific interval (e.g. 1 degree)and get corresponding velocities v and out the angle and their corresponding velocities in a table format.

3 个评论
显示 1更早的评论隐藏 1更早的评论

Arnab Sen 2016-4-26

Use '.*' and './' (element wise multiplication and division) instead of '*' and '/'

Collin Kerr 2016-4-28

buttonNumber = menu ('Select the targeted distance','8','9','10','11','12','13','14','15');

T = buttonNumber + 7;

velocities = linspace(8, 15, 1000);

angles = linspace(10, 80, 1000);

[V, A] = meshgrid(velocities, angles);

distanceImage= (V^2./a)*sin(2.*velocities)

imshow(distanceImage, []);

hold on;

contour(V,A,distanceImage)

Ive made some changes.

请先登录，再进行评论。

Could someone perhaps guide me in the right direction to figure out a way to start this code?

3 个评论
显示 1更早的评论隐藏 1更早的评论

回答（1 个）

3 个评论
显示 1更早的评论隐藏 1更早的评论

另请参阅

类别

标签

Community Treasure Hunt

Could someone perhaps guide me in the right direction to figure out a way to start this code?

3 个评论 显示 1更早的评论隐藏 1更早的评论

回答（1 个）

3 个评论 显示 1更早的评论隐藏 1更早的评论

另请参阅

类别

标签

Community Treasure Hunt

3 个评论
显示 1更早的评论隐藏 1更早的评论

3 个评论
显示 1更早的评论隐藏 1更早的评论