Need to export a 3D model

Question

Chathu 2016-10-22

0
链接

此问题的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/308557-need-to-export-a-3d-model

评论： Chathu 2016-10-24

I have set of images and i have just considered the boundary of the image. In that boundary, i have obtained points as x and y coordinates, which shown below:

x= sortedx(i);
y=sortedy(i);

then i have the z coordinate as below:

z=2*ones(1,length(line));

(Note that z is the slice thickness which apparently 2mm, here)

My question is i have stacked mat files of above mentioned boundary images. Now, my intention is to export a 3D model to paraview by converting it to VTK format. Unfortunately, out of many mat to vtk conversion functions,i was not able to solve my issue). How can i export my 3D model?

Can someone pls help.

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

请先登录，再进行评论。

请先登录，再回答此问题。

Answer 1

Walter Roberson 2016-10-22

0
链接

此回答的直接链接

https://ww2.mathworks.cn/matlabcentral/answers/308557-need-to-export-a-3d-model#answer_240153

You have boundary lines for each layer, but you do not have any information about the connection between the layers, so you cannot get a 3D geometry out without more work. How does the N'th point of the second layer relate to the N'th point of the first and third layers?

5 个评论
显示 3更早的评论隐藏 3更早的评论

Walter Roberson 2016-10-22

编辑：Walter Roberson 2016-10-23

在 MATLAB Online 中打开

Consider:

%square
temp = ones(51,51);
slice1 = zeros(125,125); slice1(38:38+50,38:38+50) = temp;
[r1, c1] = find(slice1, 1, 'first');
b1 = bwtraceboundary(slice1, [r1, c1], 'E');
x1 = b1(:,1); y1 = b1(:,2); z1 = 0 * 2.2 * ones(size(x1));
subplot(1,3,1); imagesc(slice1); colormap(gray(2)); axis image; hold on; plot3(x1, y1, z1, 'r'); hold off
%circle
slice2 = zeros(125,125); [X,Y] = ndgrid(-62:62); slice2(X.^2+Y.^2 <= 15.^2) = 1;
[r2, c2] = find(slice2, 1, 'first');
b2 = bwtraceboundary(slice2, [r2, c2], 'SE');
x2 = b2(:,1); y2 = b2(:,2); z2 = 1 * 2.2 * ones(size(x2));
subplot(1,3,2); imagesc(slice2); colormap(gray(2)); axis image; hold on; plot3(x2, y2, z2, 'g'); hold off
%rotate the square
temp3 = imrotate(temp,45);
slice3 = zeros(125,125); slice3(26:26+72,26:26+72) = temp3;
[r3, c3] = find(slice3, 1, 'first');
b3 = bwtraceboundary(slice3, [r3, c3], 'SE');
x3 = b3(:,1); y3 = b3(:,2); z3 = 2 * 2.2 * ones(size(x3));
subplot(1,3,3); imagesc(slice3); colormap(gray(2)); axis image; hold on; plot3(x3, y3, z3, 'b'); hold off

So now we have three slices to be stacked together 2 mm apart on the z. The boundaries are (x1, y1, z1), (x2, y2, y2), (x3, y3, z3)

>> [length(x1),length(x2),length(x3)]
ans =
   201    85   145

These are closed boundaries, which is why the length of the first is not 50*4 = 200. I am not sure at the moment why the third is shorter than the first. The second is smaller by way of construction -- it is deliberate in this example that the circle is smaller.

Now, should (x1(1), y1(1)) be considered to be connected to (x2(1), y2(1)), and that in turn should be connected to (x3(1), y3(1))? The first of those is the upper left corner of the square; the second of those is the top of the circle; the third of those is the top of the diamond. It might make some sense to connect the top of the circle to the top of the diamond, but the corresponding point on the square should be the middle of the top side, not the upper left corner.

Now, which point in (x2, y2) should (x1(100), y1(100)) and (x3(100), y3(100)) be connected to? There are only 85 points in (x2, y2) so you cannot go by corresponding point numbers.

I hope this demonstrates adequately that just knowing the boundary pixels of each slice is not enough to know how the layers connect together.

Technical reference for VTK file format: http://www.vtk.org/wp-content/uploads/2015/04/file-formats.pdf

Walter Roberson 2016-10-23

The document indicates that paraview would accept files that contained a bunch of 3D lines, if we arrange to output such a file. I do not, however, know what kind of processing paraview can do with such a file.

What was it you were hoping that you could do with the slices in paraview?

With situations like this, I tend to think in terms of converting the outside surface into a triangular mesh, or into a quad mesh, but it does not appear to me that meshes are one of the input types that paraview accepts.

I wonder if it would make sense to simply create a volume that was NaN (or perhaps 0) everywhere except the boundary positions? That could exported as a "structured 3D grid".

Chathu 2016-10-24

Thank you so much for your response Walter. I was hoping to get a 3D model using slices, in the Paraview. Anyway thank you so much for your kind suggestions.

请先登录，再进行评论。

Need to export a 3D model

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

5 个评论
显示 3更早的评论隐藏 3更早的评论

更多回答（0 个）

另请参阅

类别

标签

Community Treasure Hunt

Need to export a 3D model

0 个评论 显示 -2更早的评论隐藏 -2更早的评论

采纳的回答

5 个评论 显示 3更早的评论隐藏 3更早的评论

更多回答（0 个）

另请参阅

类别

标签

Community Treasure Hunt

0 个评论
显示 -2更早的评论隐藏 -2更早的评论

5 个评论
显示 3更早的评论隐藏 3更早的评论