Moving Simulink Data Into the workspace

2012 3 29
2 个回答
回答已采纳
19 次查看（30 天）

1 个投票

I am Running a Simulink Model From my GUI and i would like data from to the workspace bloacks to end up in the Matlab Workspace so i can anaylse it afterwards. The data will aperar their if i run it manually but running it through the GUI it does not appear at all.
What comand do i need to use to do this ? And which part of my GUI should i place it in .

1 个评论
显示 -1更早的评论 隐藏 -1更早的评论

Paul
Paul 2012-3-29
I have tried using the Assign function with no luck
assignin('base','helicopter_target_b', 'helicopter_target');
assignin('base',' Ctrlout_b', 'Ctrlout');
assignin('base','Heliout_b', 'Heliout');
the third variables are the names of my to workspace blocks

请先登录，再进行评论。

请先登录，再回答此问题。

 采纳的回答

Kaustubha Govind
Kaustubha Govind 2012-3-29

6 个投票

Assuming that you're using the SIM command to run the model from your GUI, you need to set the SrcWorkspace and DstWorkspace options to specify which workspaces you want Simulink to use as the source and destination workspace. By default, the variables are created in the "current" workspace, which would be the workspace of your GUI callback function. To force Simulink to always read/write to the base workspace, use:
options=simset('SrcWorkspace','base','DstWorkspace','base');
sim('mymdl',[0 duration],options)

4 个评论
显示 2更早的评论 隐藏 2更早的评论

Paul
Paul 2012-3-29
Thank you . This makes more sense than anything i have been trying
so am i right in thinking if i want the sim to run indefiatly. running using the gui and sending the data to the matlab workspace i need to do
(my sim is called manual flight)
options=simset(('SrcWorkspace','caller','DstWorkspace','base');
sim(manualflight,options)
Paul
Paul 2012-3-29
When i try different variations . I get this error message
??? Error using ==> guimanualflight>Start_Callback at 304
'DstWorkspace' parameter is not supported in this form of syntax for sim command.
Error in ==> gui_mainfcn at 96
feval(varargin{:});
Error in ==> guimanualflight at 42
gui_mainfcn(gui_State, varargin{:});
Error in ==> @(hObject,eventdata)guimanualflight('Start_Callback',hObject,eventdata,guidata(hObject))
??? Error while evaluating uicontrol Callback
Kaustubha Govind
Kaustubha Govind 2012-3-30
SrcWorkspace needs to be 'current', not 'caller'. Also, the SIM command takes the model name in the form a string.
You can try:
options=simset(('SrcWorkspace','current','DstWorkspace','base');
sim('manualflight', [0 Inf], options);
If that still doesn't work, run "docsearch DstWorkspace" and see if you find examples in the documentation. There was some change in the syntax of the SIM command recently, so it could be that you are using an older version that doesn't support the form of syntax I wrote.
Paul
Paul 2012-4-10
Thankyou this works perfectly

请先登录，再进行评论。

更多回答（1 个）

TAB
TAB 2012-3-30

1 个投票

Variables from 'To Workspace' block are saved in calling-workspace. Your way of saving them to 'base-Workspace is correct. Just make correction in assignin() call. Assign the variable values, not string.
assignin('base','helicopter_target_b', helicopter_target);
assignin('base','Ctrlout_b', Ctrlout);
assignin('base','Heliout_b', Heliout);

1 个评论
显示 -1更早的评论 隐藏 -1更早的评论

Paul
Paul 2012-4-10
This seems to not work . when I run the simulation is says that the variables have not been defined
May this be a problem from runing it from a GUI

请先登录，再进行评论。

类别

在 帮助中心 和 File Exchange 中查找有关 Simulink Functions 的更多信息

标签

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by