deploy USRP SDRu model on target hardware Raspberry Pi 3
4 次查看(过去 30 天)
显示 更早的评论
Hi everyone, I have the following problem: 1-I have installed UHD on RPi3, verify that everything is working with uhd_usrp_probe command. 2- I have a very simple model using B200 block from USPR Support Package, that transmitte a tone. 3- Then I setup the right serial number on the block. 4- I try to deploy the model on Raspberry Pi3, but fails with the following error:
### Build procedure for model: 'sdrufreqcalib2' aborted due to an error. Error executing command "touch -c /home/pi/sdrufreqcalib2_ert_rtw/*.*;make -f sdrufreqcalib2.mk all -C /home/pi/sdrufreqcalib2_ert_rtw". Details:
STDERR: make: * No rule to make target 'libmwusrp_uhd_capi.lib', needed by '../sdrufreqcalib2.elf'. Stop.
STDOUT: make: Entering directory '/home/pi/sdrufreqcalib2_ert_rtw' gcc -c -MMD -MP -MF"sdrufreqcalib2.c.dep" -MT"sdrufreqcalib2.c.o" -O0 -DMODEL=sdrufreqcalib2 -DNUMST=1 -DNCSTATES=0 -DHAVESTDIO -DONESTEPFCN=1 -DTERMFCN=1 -DMAT_FILE=0 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=0 -DMT=0 -DCLASSIC_INTERFACE=0 -DALLOCATIONFCN=0 -DTID01EQ=0 -D__MW_TARGET_USE_HARDWARE_RESOURCES_H__ -DARM_PROJECT -D_USE_TARGET_UDP_ -D_RUNONTARGETHARDWARE_BUILD_ -DRT -DSTACK_SIZE=64 -DONESTEPFCN=1 -DTERMFCN=1 -DMAT_FILE=0 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=0 -DMT=0 -DCLASSIC_INTERFACE=0 -DALLOCATIONFCN=0 -DTID01EQ=0 -DARM_PROJECT -D_USE_TARGET_UDP_ -D_RUNONTARGETHARDWARE_BUILD_ -DRT -DSTACK_SIZE=64 -DMODEL=sdrufreqcalib2 -DNUMST=1 -DNCSTATES=0 -DHAVESTDIO -I./ -o "sdrufreqcalib2.c.o" "sdrufreqcalib2.c" gcc -c -MMD -MP -MF"sdrufreqcalib2_data.c.dep" -MT"sdrufreqcalib2_data.c.o" -O0 -DMODEL=sdrufreqcalib2 -DNUMST=1 -DNCSTATES=0 -DHAVESTDIO -DONESTEPFCN=1 -DTERMFCN=1 -DMAT_FILE=0 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=0 -DMT=0 -DCLASSIC_INTERFACE=0 -DALLOCATIONFCN=0 -DTID01EQ=0 -D__MW_TARGET_USE_HARDWARE_RESOURCES_H__ -DARM_PROJECT -D_USE_TARGET_UDP_ -D_RUNONTARGETHARDWARE_BUILD_ -DRT -DSTACK_SIZE=64 -DONESTEPFCN=1 -DTERMFCN=1 -DMAT_FILE=0 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=0 -DMT=0 -DCLASSIC_INTERFACE=0 -DALLOCATIONFCN=0 -DTID01EQ=0 -DARM_PROJECT -D_USE_TARGET_UDP_ -D_RUNONTARGETHARDWARE_BUILD_ -DRT -DSTACK_SIZE=64 -DMODEL=sdrufreqcalib2 -DNUMST=1 -DNCSTATES=0 -DHAVESTDIO -I./ -o "sdrufreqcalib2_data.c.o" "sdrufreqcalib2_data.c" gcc -c -MMD -MP -MF"linuxinitialize.c.dep" -MT"linuxinitialize.c.o" -O0 -DMODEL=sdrufreqcalib2 -DNUMST=1 -DNCSTATES=0 -DHAVESTDIO -DONESTEPFCN=1 -DTERMFCN=1 -DMAT_FILE=0 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=0 -DMT=0 -DCLASSIC_INTERFACE=0 -DALLOCATIONFCN=0 -DTID01EQ=0 -D__MW_TARGET_USE_HARDWARE_RESOURCES_H__ -DARM_PROJECT -D_USE_TARGET_UDP_ -D_RUNONTARGETHARDWARE_BUILD_ -DRT -DSTACK_SIZE=64 -DONESTEPFCN=1 -DTERMFCN=1 -DMAT_FILE=0 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=0 -DMT=0 -DCLASSIC_INTERFACE=0 -DALLOCATIONFCN=0 -DTID01EQ=0 -DARM_PROJECT -D_USE_TARGET_UDP_ -D_RUNONTARGETHARDWARE_BUILD_ -DRT -DSTACK_SIZE=64 -DMODEL=sdrufreqcalib2 -DNUMST=1 -DNCSTATES=0 -DHAVESTDIO -I./ -o "linuxinitialize.c.o" "linuxinitialize.c" make: Leaving directory '/home/pi/sdrufreqcalib2_ert_rtw'
ANY HELP, MATLAB SUPPORT?
0 个评论
回答(1 个)
另请参阅
类别
在 Help Center 和 File Exchange 中查找有关 Raspberry Pi Hardware 的更多信息
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!